Cannot login to wbr-2310 router's config page

Hi,

Welcome to Fixya. If you want to make your connection secure by using a password you need to access the router settings page and change the security type. Follow the instruction below on how to make the connection secure.

If you want to setup a password or security on your router you need to access the Wireless Settings Page. To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.0.1, the Default username is admin and the password is blank. Go to Wireless Settings and under Wireless Security Mode select either WEP, WPA, WPA2 then create a personalize Passphrase. Passphrase serves as the password on the network to make it secure.

Thanks for using Fixya.

ok you need to open your internet browser and in the address bar enter 192.168.0.1 then a login prompt will come up enter admin for the user name and leave the password blank. then when you get to the router configuration page select the setup wizard and follow it to the end and that should be it, if you still have problems uninstall the setup that you did from disk they may confict. ok hope that helps and just in case you dont have the manual here is the link to the support page for your router http://www.dlink.com/products/?tab=3&pid=WBR-2310&rev=WBR-2310 please let me know if i can assist you any further and how you go.

Who is you ISP? if you're using cable connection follow these steps:

1. Connect modem to WAN port of the WBR-2310
2. Connect computer to port 1 of the WBR-2310
3. Open web browser (IE, firefox,chrome,safari), and type in 192.168.0.1 into your address bar
4.Into the log-in page username:admin password: (none)
5.click on "SETUP"
6. Click on "MANUAL CONFIGURE"
7..in the Internet connection type, make sure that it must be in DYNAMIC IP DHCP
8. Click on CLONE YOUR PC's MAC ADDRESS button(notice that mac address will change after you click on that button)
9. Click on SAVE settings now and it will count down click on Continue after that
10. Then Try to ACCESS Internet

/... but if still you cannot access Internet try to power cycle the modem and the router.. follow these steps also

1. turn off bothe modem and router (just unplug the power cord)
2. after 1 minute, TURN ON first the modem,
3. after 1 minute again, TURN ON the router
4. after 1 minute try to access Internet

But if still no Internet connection, please look for the brand of your modem if it is speedstream 5100 or hugesnet or actiontec modem because those modem have the same IP address with your DLINK router and you need to change the IP address of your DLink then....

Further questions? call 1-877-453-5465 (US), 1-800-361-5265

Hope this will help you. Goodday

So this is only the problem of your Internet Explorer, you are trying to access your Router on its Firmware to configure IP Address to your Games but unfortunately you cannot go on to the Firmware. You got spam by any spyware at this point, all you have to do is use another explorer which are good for opening such program. How about to try Mozilla Firefox or Chrome X Explorer. See what you can do to this explorer to open up your Router. Hope this might help you and good luck for your gaming.

you have to change your channelk type in your wi fi router.
For that access your router with following link

http://192.168.1.1 or
http://192.168.0.1

if you have belkin router
http://192.168.2.1

type user name as "admin" and password is "admin" or blank or "password"

then go to wi fi ->advanced setup chang channel type 4 ,6 ,11
change chanel type 1 by 1 and check signal strength.
everyt time save settings and restart both computer and router after save settings.

Thanks for using fixya.
Please rate this solution if it helps.

you need to configure the wireless on the router through a cable connection at first. after logging in on the router (default admin login and password should be mentioned in the router's manual) you can enable the wireless and the DHCP. to access the router, open an internet browser window and surf to the address http://192.168.0.1, where you will be asked to fill in the admin password.
please keep us posted on any evolution

Try to bypass the router and connect to your modem. Make sure you have Internet connection.
>If you have Internet connection. connect back your modem to the router.
>access the configuration page of your router.
>If you are given a specific IP by your Internet Service Provider, use that one.
>Login to your Dlink (type in on the address bar 192.168.0.1)
>Click Setup and Internet > Click on Manual Configure
>My Internet connection would be Static IP
>Type in your IP address, Subnet Mask, Default Gateway, Primary and Alternate DNS
>Click on Save Setting on top.

but if your Internet Service Provider did not provide you those informations
> Under My Internet connection Type choose DYNAMIC IP
>Click on Clone Your PC MAC address
>Click on Save Settings
>If it ask you to reboot, click on Reboot.

>At the very top click on Status
>Under Status look for WAN
>Under WAN look for IP address
>If you have values beside from zero it means you have Internet connection otherwise, call your dlink manufacturer for manual configuring your router for Internet connection.

Disable the IPV6 and use the IPV4 then try accessing the configuration page of the router and configure the Internet Settings

If you dont know your wpa network key try to reconfigure your wireless network again.

Access the configuration page of your router.
>Type on the address bar 192.168.0.1
>On login type Admin leave password blank. if you set up a password or the login page use that one.
>Once inside the Dlink Page
>Clik Setup and on the left side click wireless setting.
>If given the option to click on manaul wireless connection setup click on it.
>Once you have the wireles window
>try to change the network name to a new one and scroll down
>Under security choose WPA security (enhanced)
>Scroll down and under the Passphrase type in your new network password or security key and confirm it.
>Click on Save Settings
>If it asks you to reboot then reboot it, if not, its ok.

At the back of the router is a tiny pinhole. Using a pen try to press it for 15 secs and try to access the page using the 192.168.0.1