Question about Bosch Nexxt Premium WFMC6400UC Front Load Washer

Open Question

Bosch 6400 washer drum won't turn

Main motor doesn't turn

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: how do I turn off the beepers on my Bosch washer

To turn the beep off (or volume down) on the Exxcel 7 (BOSCH WAE24468GB you do the following:
1. Turn setting dial to off. 2. Turn dial one step clockwise (wait for panel to light) 3. Keep finger on 'RPM' button and turn dial another step clockwise and release finger. 4. The default setting of '2' should appear on the display, this represents the Button Signal Volume 5. Pressing 'Ready in' button cycles through the volume settings from 0 (off) to 4 (very loud!). 6. Turn dial another step clockwise to set the 'Information Signal Volume', which is also set to '2' by default. This is the one that annoys everyone at the end of the cycle!
All the manuals are on the Bosch website, if you know the model code.

Posted on Jan 13, 2010

Ad
richroth

Richard Roth

  • 9472 Answers

SOURCE: my Bosch next 300 washer doesn't spin as fast as it did. It leaves the clothes wet and some water in the drum. No error code comes up? How do we fix it?

If the tub still moves but it's just not spinning that fast (and the water is draining out), then that means your motor control board has just started to fail and it will need to be ordered and replaced to fix the issue. If you pull the washer out and remove the back panel, there is a control board mounted to the floor under the tub. This is the motor control board and it will need to be ordered and replaced to fix the issue.

Posted on Oct 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MyGGL39608 GOLD'S GYM Trainer 480 belt doesn 't turn Whats the problem?


You must need to replace the Complete Controller Board Motor.
Has 3 functions power supply: 1) Console Board 2) Elevation Motoro 3) Main Motor.
Some IGTBs has been failed. Replace. Treadmill How To Replace Control Board
Blessing
cuadra2016@yandex.com
cell+whatsAPP:+50588611441

Nov 24, 2017 | Exercise & Fitness

1 Answer

Beater bar motor quit, now the main motor quit. Replaced the on/off switch. still nothing


see this causes and fix it. God bless you
If the vacuum cleaner motor doesn't run the on - off switch might be turned off or defective. Test the switch with an Ohm meter or continuity checker.
If the vacuum cleaner motor does not run the motor itself might be burned out. Check the power switch first to be sure the motor can get power. Then, be sure the motor shaft can turn freely, that nothing is obstructing it. If the motor can turn freely and is getting power but still won't run it will need to be replaced.
9_28_2012_11_21_42_am.jpg9_28_2012_11_21_57_am.jpg

Sep 27, 2012 | Vacuums

1 Answer

My refrigerator dose not cool freezer or main section, motor and fan work


check for the thermostat knob which malfunction doesn't turn on.

Aug 10, 2012 | Refrigerators

1 Answer

Frigidaire washing machine (FTW3011KW0) runs through all cycles, agitates, pumps out water, but doesn't spin, nor does the motor attempt to spin during the spin cycle


Your main switch needs replaced. The motor that drives the switch operates because it goes through the other cycles, so the switch must be bad.
murf427

Jul 31, 2012 | Frigidaire Washing Machines

1 Answer

BLOWER MOTOR DOESN'T SHUT OFF


Hello, if the only way to shut off the motor is to turn off the main power then the relay on the integrated control board is faulty. You can try tapping on the relay to turn it off but eventually the board will need to be replaced.

Jun 04, 2012 | Amana Heating & Cooling

1 Answer

I have an athletech performance treadmill it won't turn on on button doesn't click as does the off button


Dear Sir:
1) Try to reset the c. breaker in your treadmill.
2) Inspect if your see some loose wires.
3) Open the keypanel and tight the flexible cord or ribbon cables.
4) Tight the connector coming from display planer to lower boar or main motor board.
5)Test the Transformer for there are voltage in primary and secondary winding.
6) Measure the input to the power board
7)See there are +5VDC to the main motor board and display board?
8) Run the calibration Software read your user manual or see under the Hood the motor the instruction for more easy diagnose and troubleshooting . Attached is my block diagram that I did design for purpose of diagnose. sincerely. God bless you

ernesto cuadra
managua, nicaragua. c.a.
2_16_2012_11_55_47_pm.gif

Feb 12, 2012 | Exercise & Fitness

2 Answers

Washer won't agitate or spin


Hello there and welcome to fixya
there are several things that you will need to check first ok please verrify the following
It doesn't pump or spin
If it doesn't pump water out or spin, check to see if the motor is running, then proceed as follows:
If the motor is running, your washer probably has a frozen pump pulley or a broken pump belt. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn't turn freely--if it's frozen or stiff--replace it. If the pump belt is broken or looks quite worn, replace it--but be sure to check the pump pulley before you change the belt.
If the motor isn't running, the lid switch may be defective. If so, the washing machine can't spin and may not function at all. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.
It pumps, but doesn't spin
If your washer pumps out the water but doesn't spin, check these:
The lid switch may be defective. If it is, the washing machine doesn't spin. The switch is inside the washing machine main housing near the door frame. Often you have to raise or open the top or front of the washing machine to get to the switch. If it's defective, you need to replace it.

Sep 07, 2011 | GE Profile WPRE6100G Top Load Washer

1 Answer

"Service Call Error E54"


This error code indicates a fault with the Main Motor. Either it's jammed or unusable. Unplug the printer from the power source, leave it for around 30 minutes, . While it's turned off, remove the cartridges, check for any damage, then put them back in. After tha, then reconnect it to the power and turn it on again. If this still doesn't clear the code from the display then you'll need to see a Brother service agent to have the main motor replaced.

May 02, 2011 | Brother HL 1650 Laser Printer

1 Answer

I put an envelope in the printer since then its doesn?t work, I tried to restart, change the drum and push in a paper by the special slot and it still doesn?t work. Just the motor is turning and the excess...


reinstall printer
then go into properties, click main, where it says TYPE click plain paper, where it says SIZE click on the envelope size you want to use, then click ok

Feb 02, 2009 | Brother HL-2040 Laser Printer

Not finding what you are looking for?
Bosch Nexxt Premium WFMC6400UC Front Load Washer Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

jimorris77

Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...