Looking for CRA 470 PF 3.6 M Ohm 125 VAC

You have pretty much ruled out everything in that machine. The only thing left to check is the wiring to the plug in the building and the breakers

Special Tools

• EN-235-6 Installer
• EN-470-B Angular Torque Wrench
• EN-658-1 Installer

For equivalent regional tools, refer to Special Tools.

1. Install a NEW crankshaft position sensor reluctor ring?(1) and the 3?bolts?(2).
2. Tighten the 3?bolts?(2) to 10?Y?(89?lb?in).
3. Lubricate crankshaft, crankshaft bearings and crankshaft bearing cap tie plate with engine oil.


4. Install the 4?upper crankshaft bearings?(2) and the crankshaft thrust bearing?(3).
5. Install the crankshaft?(1).

Note: The thickness of the sealing bead should be 2?mm?(0.0787?in).
6. Apply sealing compound?(1) to the outer rim of the groove on the crankshaft bearing cap tie plate. Refer to Adhesives, Fluids, Lubricants, and Sealers.


Note: The complete installation procedure should not take longer than 10?minutes.
7. Install the 4?lower crankshaft bearings?(3) and the lower crankshaft thrust bearing?(4).
8. Install the crankshaft bearing cap tie plate?(2).
Note: Do not reuse the old bolts.
9. Install the 10?NEW inner crankshaft bearing cap tie plate bolts?(1).

Caution: Refer to Fastener Caution. Caution: Refer to Torque-to-Yield Fastener Caution.
10. Tighten the 10?inner crankshaft bearing cap tie plate bolts in the sequence shown and to the following specifications:
1. Tighten the inner crankshaft bearing cap tie plate bolts to 25?Y?(18?lb?ft).
2. Tighten the inner crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
3. Tighten the inner crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.


Note: Do not reuse the old bolts.
11. Install the 12?NEW outer crankshaft bearing cap tie plate bolts?(1) and tighten to the following specification:
1. Tighten the outer crankshaft bearing cap tie plate bolts to 10?Y?(89?lb?in).
2. Tighten the outer crankshaft bearing cap tie plate bolts an additional 60?degrees, using the EN-470-B wrench.
3. Tighten the outer crankshaft bearing cap tie plate bolts an additional 15?degrees, using the EN-470-B wrench.



12. Install the crankshaft position sensor?(1) and a NEW crankshaft position sensor seal ring?(2).
13. Install the crankshaft position sensor bolt?(3) and tighten to 8?Y?(71?lb?in).


Note: Lubricate the crankshaft rear oil seal.
14. Install the crankshaft rear oil seal?(1) with EN-235-6 installer?(2).



15. Use EN-658-1 installer?(1) to strike the crankshaft rear oil seal.



My database showed this info. Only the inner 10 showed a sequence. The outer 12 didn't.

https://www.google.com/search?q=97+cajun+boat+wiring+diagram&rlz=1C1CHBF_enUS697US697&tbm=isch&imgil=pVOOLMT3I_7NdM%253A%253BKV1IffebLg65tM%253Bhttps%25253A%25252F%25252Fwww.boatdesign.net%25252Fthreads%25252Ftypical-wiring-schematic-diagram.11931%25252F&source=iu&pf=m&fir=pVOOLMT3I_7NdM%253A%252CKV1IffebLg65tM%252C_&usg=__v5zjhDvp6zjDMzKORUS9p8JrX48%3D&biw=1266&bih=895&ved=0ahUKEwiG8PPmztLWAhUk7IMKHaVLBkAQyjcIPw&ei=v4vSWcaUB6TYjwSll5mABA#imgrc=pVOOLMT3I_7NdM:

Steven, I will post links for you , to get manuals and info.
press the helpful button and follow me on fixya for more tips and info

http://store.payloadz.com/details/571079-ebooks-technical-olympic-fly-reel-470-76-56-schematics-and-parts-sheet.html


https://www.google.ca/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0ahUKEwicw-mz1PfKAhWDPB4KHVK8DhsQFggnMAI&url=http%3A%2F%2Fnewyorkfishingexchange.com%2Ffishing%2Folympic-fishing-reel%2F&usg=AFQjCNFJSJQ4MXgI0NzUYoV8kSGgT7eE_A

470 Ohm 5W Resistor Wire Wound 5 Tolerance from www parts express com

The above link will give you a source on the 5 watt 470 Ohm resistor. I assume it is from a vehicle and probably adds a load to make turn signals function. Since LEDs use considerable less power then tungsten lamps additional load is added to make the older flashers work.

an air horn contains hoses compressor and tank and etc go to jcwhitney and look up the best hors hadley they haqve oyhers but hadleys the best must be willing to spend money but they sell electric ones you need also

It appears to be a 430 ohm 5 Watt FLAMEPROOF resistor... The resistance value could also be 470 ohms...

Here is link to a 430 ohm:

http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=PPC5W430TB-ND

Here is link to schematic, however the resistance value is blurred but starts with 4 and is three digits leaving only 430 or 470 as the value:

http://elektrotanya.com/peavey_delta_blues_sch.pdf/download.html

Mouser electronics.
Digikey
some surplus places like all electronics.

Please make sure you purchase the right wattage... sorry covering by bases for you...

cant goto Radio shack and get a 470 Ohm resister in a 1/2 watt... it will burn up...
check the additional markings on the bad one...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/lisa_52daba487e5b4d53

1 hp= 750 watts
125 vac = 125 volts alternating current, wall outlets
5 amp= 5amps

125vac x 5amps= 625 watts

a timer is a switch with a clock on it. just like a switch in a lamp cord.

R106 is a .5 ohm. It is green,black,gold, and silver. I believe it is a 1/2 watt resister
R103A is a 27 ohm and R108A is a 470 ohm resister.I have no schematic.












.