Question about Frigidaire Affinity ATF7000ES Front Load Washer

Open Question

What is code f64? on frigidare affinity clothes drire mean?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 156 Answers

SOURCE: frigidare affinity front load washer

is thse the digital panel if so the control board needs replaced

Posted on Feb 27, 2008

Ad
  • 240 Answers

SOURCE: ERROR CODE 68 ON AFFINITY ATF7000EE

check tech sheet located inside washer cabinet at bottom. remove lower kick panel to access.

Posted on May 04, 2008

  • 3 Answers

SOURCE: I am experiencing an error

Clean the cold water filter on the back, then try again. This should work. Mine was doing the same thing and the repairman had no idea what it meant.

Posted on Jan 15, 2009

MakeupWizard
  • 39 Answers

SOURCE: What does error code E59 means on a Frigidaire

Hiya
if you have pressed any of the buttons during a wash cycle then you will be given an error message on the display to change the wash options once started you must 1st pause the wash before making any changes, this i think would be the main reason for such an error to appear however you can download your operaters manual at http://www.frigidaire.com/manuals
if you do not already have it & from there you may be able to have a read & work out why you received this message alternativly from the site you will get a link to a contact us section where you may be abal to ring the customer services & then have the assistant check the code for you..

Hope this helps

Posted on Apr 22, 2010

Macmarkus
  • 2605 Answers

SOURCE: frigidare affinity error code E23

Hello, welcome to FixYa.
I understand you have a Frigidaire Affinity ATF6000 series washer with an error code E23, correct ?
If that is indeed the error code you receive in the display it is potentially bad news unfortunately, as that indicates either loose wire (fingers crossed) or a failed drain pump relay on the control board. This is how it is described in the Frigidaire service tech manual.
macmarkus_1089.jpg

Further to this, if it is not a loose wire at the pump or on the control, the only remedy is to replace the control board, unless you are proficient at electronic repairs (including soldering techniques) and can purchase an exact relay and replace just the relay...though that doesn't guarantee the control hasn't suffered collateral damage in the process.
A new control is part #134523106...
it is available at several on-line parts vendors such as "repairclinic.com" or "searspartsdirect.com" to name a couple as these links will provide.
http://www.repairclinic.com/PartDetail/Main-Control-Board/134523106/1191145
http://www.searspartsdirect.com/partsdirect/part-number/Frigidaire-Parts/Washer-Parts/134523106/0026/417/Model-ATF6000ES1/1428/0153200?keySuffixId=NA&pathTaken=partSearch&pathRender=modelComponent&documentCompId=R0604038&diagramPageId=00001&productTypeId=0153200&searchModelNumber=ATF6000ES1&subCompDesc=Control%20panel&brandDesc=FRIGIDAIRE&modelDesc=WASHER&blt=11
Hope this answers your question and helps you move forward. Let me know how you make out or if anything isn't clear. Good luck and thank you for choosing FixYa today.
Regards,
Macmarkus :)

Posted on Oct 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant open the front door seems like its locked


My frigidaire affinity dryer displays LOC - Fixya

www.fixya.com/support/t4561247-frigidaire_affinity_dryer_displays_loc
my frigidaire affinity dryer displays LOC and will not allow me to press any buttons what does that mean? please - Frigidaire Affinity 5.8 Cu. Ft. Gas Dryer question. ... Hi i have a front load frigidare dryer and it displays the cycle time when you press start but it blinks back & fourth to loc & whatever cycle its ... Open Questions:.

Nov 23, 2015 | Frigidaire Affinity 5.8 Cu. Ft. Gas Dryer

1 Answer

Dripping water in frigidare. Affinity dryer


I appreciate your post, Joe Ivey!

From the information you have provided your Frigidaire dryer is leaking water inside the tub when clothes are drying. It sounds like your water valve may be leaking. You may want to have a professional technician out to your home to properly diagnosis your dryer this will help to avoid any unnecessary part purchases or future issues. Hopefully this was helpful. -Matt

Jan 11, 2015 | Frigidaire Dryers

1 Answer

My frigidare affinity shuts down mid cycle , and has to be restarted many times in order to finish a load of clothes


Remove top of washer by removing screws in back of top. You should see the tech sheet. Use this to retrieve any error codes.
A common problem with these is a bad door switch. (The part the strike goes into. If this is the case you should come up with error code for it.

Mar 11, 2014 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

My Frigidare Affinity front load washer doesn't pump water on the Normal cycle.


Check the water inlet electro valve at the rear of the washer and make sure it is working.

Jul 25, 2017 | Frigidaire Washing Machines

1 Answer

Affinity frigidare front load washer won't start. It beeps with message flashing (DR)


Hello zabbster - Typically the DR or DO error code indicates that the door switch is not closed. Make sure that the door lock is completely closed. If the door is closed, make sure the door latch is not broken. If the latch is broken, you may possibly need to replace the door lock switch.

Sep 25, 2012 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Hi i have a front load frigidare dryer and it displays the cycle time when you press start but it blinks back & fourth to loc & whatever cycle its then you press buttons and it beeps continuosly...


that's a lot of kids... according to the Frigidaire wiring diagram and codes list E68 means a key is stuck or bad board. You can enter function test mode and check which button is at fault. Hope this helps Tim

p.s. here is a thread:


http://forum.appliancepartspros.com/dryer-repair/143380-frigidare-affinity-dryer-e68-error-code.html

Apr 06, 2011 | Dryers

1 Answer

Frigidare affinity model # atf6000es won't spin in


sometimes in the bottom right hand corner of the machine there is a little face plate and allows to you unclog foreign material that collect over time.

Nov 06, 2009 | Frigidaire Affinity ATF6000ES 3.5 Cu. Ft....

1 Answer

I am experiencing an error code during my wash cycle of E10... I have a frigidare affinity series washer.


Clean the cold water filter on the back, then try again. This should work. Mine was doing the same thing and the repairman had no idea what it meant.

Jan 08, 2009 | Frigidaire Affinity ATF7000ES Front Load...

1 Answer

My Frigidare Affinity Front Load Electric Dryer ruins my clothes!


Sadly FIXYA does not know why things mess up

Sep 30, 2017 | Dryers

2 Answers

Frigidare affinity front load washer


is thse the digital panel if so the control board needs replaced

Nov 10, 2007 | Frigidaire ATF6000ES Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

302 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

J. Bradshaw

Level 2 Expert

121 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...