Question about Nordic Track Commercial 1750 Treadmill Incline Motor

1 Answer

What is wrong with and how can I fix the incline on my Nordictrack commercial 1750 treadmill?

Nordictrack commerical 1750 is stuck at -3 degrees elevation and won't incline. When incline button is pressed, it tries to go up for a second and then goes back down for a second. This repeats 4 or 5 times and then stops. It seems as though it is stuck. Is there a way to free it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 749 Answers

This sounds as though the motor is bad, they cost around $130.00, ther is a n electronic controller that controls it, but as it is trying to raise I would think that the switch and controller are functioning. Best of luck and please post back f this helps.

Posted on May 25, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 103 Answers

SOURCE: NordicTrack Z7xi treadmill console buttons not working

Hello there. It sounds as if you may have a button stuck on your console. Thus not allowing any other buttons to be pushed. (i.e. the 4 beeps). This is usually caused by the i-fit buttons (silver buttons on the front). If the machine is only 4 months old you should still be under warranty (1 year) I believe. This problem in most instances requires the console be replaced. You can contact nordictrack through iconservice.com or by using the number on the fron of your users manual.
Good Luck! Tim

Posted on Dec 16, 2009

maxtreadmill
  • 832 Answers

SOURCE: My treadmill is stuck in the max incline position

If the incline moves but only just a bit, it could be a problem as simple as the gearbox on the motor being jammed. We remove the motor from the treadmill, reconnect the wiring, and then try to run the incline motor outside the treadmill. Many times, this will unjam it if that is the problem and then reinstalling it in the treadmill will get it to work. If you have the same problem or it doesn’t run outside the machine and you can hear it try to work, you need to replace the incline motor.

Posted on Jun 11, 2010

maxtreadmill
  • 832 Answers

SOURCE: I have the Nordictrack C2500, and for the second

You have a wire harness that attaches the upper board to the lower board. You may have to pull that harness thru the uprights ( Attach a fishing line so you can either pull a new harness thru or the original one ) and inspect it for snags crimps or broken wires also use a meter to a continuity check on the harness ends. Since the the command signals travel thru this harness also check all connections on the lower board. Its starting point

Posted on Jun 11, 2010

  • 218 Answers

SOURCE: My Nordictrack treadmill seems to

it is trying to calibrate itself, let it go the whole way up and then down without interrupting it. Then it should be fine.

Posted on Aug 11, 2010

outfield502
  • 79 Answers

SOURCE: My Nordictrack commercial 1500 is stuck at 12%

need to flip side and with a wrench 1 / 2 or 9 / 16 loosen the screw of motor base and try to press the down key and if so work you should Lift motor replacement

Posted on Sep 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a NordicTrack commercial 1750 treadmill. My console contols do not work and the ifit screen does not complete startup. What can I do to troubleshoot the problem?


The Controls Are Not Working on a NordicTrack Treadmill ...

www.livestrong.com > Sports and Fitness
Jun 1, 2015 - The Controls Are Not Working on a NordicTrack Treadmill ... Many glitches involving the controls on the console can be solved relatively quickly with some simple .... How to Use the iFit Videos with My NordicTrack Treadmil...

Nordictrack commercial 1750 that Icon can NOT fix - YouTube

? 3:52
https://www.youtube.com/watch?v=ILBbzyUXn2Q
Dec 16, 2011 - Uploaded by gerg6060
Nordictrack commercial 1750 that Icon can NOT fix ... I'll NEVER buy another Nordictrack again, Smooth or ...

[PDF]View Manual in PDF Format - NordicTrack

https://service.nordictrack.com/.../pdfDownload.do?...1...

NordicTracktreadmill is not working properly. (See. TROUBLESHOOTING on ... COMMERCIAL 1750 treadmill. ... Console. Book Holder. Key/Clip. Power Switch. Walking Belt. Foot Rail. Power Cord ... Set the treadmill in a cleared area and remove all packing materials. Do not dispose of .... Each workout automatically controls the speed.

Dec 28, 2015 | Nordic Track NordicTrack COMMERCIAL 1750...

1 Answer

I have the 1750 Commercial Treadmill and the screen is "froze" on the program for the sd card or WiFi. When I push on the stop button or unplug and replug in the power it still is STUCK on that screen. ...


use this steps and fix it. God bless you


Step 1

Plug the power cord into a UL 1449 single-outlet surge suppressor and then plug the surge suppressor into an electrical outlet that is not GFCI-equipped if the power does not turn on. If the treadmill is plugged in and the power still does not work, make sure the key is in the console and that the Reset/Off circuit breaker has not been tripped. Press the switch to "Reset" if it has been tripped.

Sponsored Links
Gym Equipment Choose from 1M+ Verified Suppliers. Contact Directly & Get Live Quotes! www.alibaba.com/Gym-Equipment

Step 2

Check the Reset/Off circuit breaker if the power switches off while in use. Wait five minutes and switch the button to reset. Check that the power cord is still plugged in securely; pull the plug out and plug it back in after five minutes. Pull out the console key and reinsert to see if the machine will turn back on.

Step 3

Place the chest pulse sensor tightly right underneath your pectoral muscles or breasts for it to operate properly. Position it lower or higher on your chest if it does not work properly. Wet the electrodes with a saline solution. Walk near the walking belt's center within an arm's reach of the console.

Step 4

Remove the console key and unplug the treadmill to loosen the walking belt if it slows when in use. Turn the rear roller bolts counterclockwise with the hex key 1/4 of a turn until you can lift the walking belt's edges 3 to 4 inches from the platform.

Step 5

Remove the key and unplug the treadmill to adjust the walking belt if it is off-center or slips when in use. Loosen the rear roller bolts with the hex key and reposition the walking belt. Tighten the roller bolts. Walk on the treadmill to determine if the walking belt is centered. If not, loosen the roller bolts again and make adjustments until the walking belt is centered.

Step 6

Recalibrate the incline system if the treadmill's incline does not adjust correctly. Press the "Incline" button and remove the console key. Wait a few seconds and replace the console key. The incline will automatically recalibrate by moving to the maximum incline level and then the minimum level.

Step 7

Press the "Stop" button for a few seconds to turn off the demo mode if the console display stays lit after you remove the console key.

Read more: http://www.livestrong.com/article/241157-nordic-track-treadmill-troubleshooting/#ixzz2geWlKdPR

Oct 02, 2013 | Nordic Track NordicTrack COMMERCIAL 1750...

1 Answer

Nordictrac 1750 stuck in download files mode..


you must restore to the original factory, and see was happening.
Ohterwise the software can be corrupted.use antivirus+antimalware

God bless you

Jun 14, 2013 | Nordic Track NordicTrack COMMERCIAL 1750...

1 Answer

Treadmill stuck in -3 incline


Double check that all connections are secure, especially the console cable. Unplug and reconnect the console cable to verify.
Unplug treadmill from wall outlet. Wait 60 seconds, allowing lower board to discharge built-up energy.
Remove motor cover.
Verify that there are no lights lit on the lower circuit board.
Verify that all wires are securely and correctly placed on the lower circuit board, especially the large wire harness on the top of the circuit board with 12 different colored wires coming out of it.

Dec 09, 2011 | Nordic Track NordicTrack COMMERCIAL 1750...

1 Answer

My 1500 incline is stuck at 12% and won't respond to re-calibration


This is something you can fix yourself.
I suggest you get in contact with Icon Fitness.

Apr 04, 2011 | Nordic Track NordicTrack Commercial 1500...

1 Answer

Nordic track 1750 stuck on ifit demo mode


i think you have to add the red magnetic key in place before starting it

Jan 04, 2011 | Nordic Track NordicTrack COMMERCIAL 1750...

2 Answers

My Nordictrack commercial 1500 is stuck at 12% incline and won't go nor up or down. How do i fix?


need to flip side and with a wrench 1 / 2 or 9 / 16 loosen the screw of motor base and try to press the down key and if so work you should Lift motor replacement

Sep 12, 2010 | Nordic Track NordicTrack Commercial 1500...

Not finding what you are looking for?
Nordic Track Commercial 1750 Treadmill Incline Motor Logo

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

135 Answers

Treadmill Repairs...
Treadmill Repairs...

Level 2 Expert

338 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...