Question about Washing Machines

1 Answer

Why is there an 'SF' code showing and continuous beeping from our Simpson encore 756

Our Simpson Encore 756 washing machine stops its wash cycle, continuously beeping while showing an 'SF' code. What does this code mean & what do we need to do to correct /avoid the problem? Thanks much, Jonno.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 181 Answers

There are different sf codes for different faults. try googling the sf number fault to find problem.

Posted on May 25, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Simpson encore 556 display SF on the Display panel. What's it mean?


If the control panel detects that the motor is not rotating then it will beep & show that fault.

Feb 26, 2016 | Simpson Washing Machines

1 Answer

My washing machine goes fine until half way through wash then comes up with error code PU and beeps until I turn it off...will not drain out the water? Simpson encore 556


simpson encore pu Unsolved Problems - Fixya

www.fixya.com/unsolved_problems/simpson_encore_pu
Unsolved problems for simpson encore pu question. Get free help ... My simpson encore 757 shows PU error code. What is this? ... Simpson encore 556. Aug 22 ...

Sep 10, 2015 | Simpson Washing Machines

2 Answers

WHAT IS SF CODE ON WASHING MACHINE


A bit difficult to provide guidance without knowing make and model of washing machine. But in some washers like Simpson SF code means motor overload and could occur due to too much suds in the wash. Maybe using incorrect detergent.

Aug 29, 2014 | Washing Machines

1 Answer

Simpson encore 605 fault code are as follows during wash process stop suddenly, strat to beep and all lights are gone except the Maxi light . It flashs while beeps


Hi, my Simpson encore 605 wash machine wash on the half way keeps beeping, and the maxi is keep flashing. What kind problem it is?
Cheers!

Feb 12, 2012 | Washing Machines

1 Answer

SIMPSON 816 ENCORE WASHING MACHINE ERROR MESSAGE


Hello

Try running the washer through rinse/spin cycle,then normal cycle without any detergent.

SF is suds failure,or too much detergent or wrong type of detergent.You need to use H E type detergent.

This should clear the machine out.

Apr 01, 2011 | Electrolux Washing Machines

1 Answer

Simpson encore 756 flashes sf


Motor overloaded wait 15 minutes, press start stop.

Oct 04, 2010 | Washing Machines

1 Answer

Says sf on screen Simpson encore 807


i have a Simpson encore 807 & its displays DF what does that mean... as it keeps beeping...

Jun 30, 2009 | Washing Machines

2 Answers

Simpson encore 806 washing machine beeping and screen showing DF


DF means the temperature sensor is faulty. Replace it. Get a new one from your Simpson agent. Turn power off. Open panel by removing the 3 screws at the rear of panel & swing it up. If you are standing behind the machine look on the left hand side at the top of the circuit board. You will see a small white plug with 3 wires (red-white-black) Very carefully pull this plug toward you off the 3 pin base. The other end is the sensor pushed into the water inlet chamber. Pull it out. Push new sensor into water chamber (make sure black rubber o-ring is on it) Push wiring plug back onto 3 pin base. It can only go on one way. Do not force it or twist it as the 3 pins can be easily broken or damaged. Then close panel & power up.

Jan 11, 2009 | Washing Machines

2 Answers

Simpson washing machine encore 756 displays error df and will not complete cycle


our simpson encore 756 flashes SP can anyone tell us what it means and how do we fix it thanks mark

Aug 03, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,450 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Brad Brown

Level 3 Expert

18087 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...