Lakewood HV 18-c Floor / Box Fan Logo

Related Topics:

A
Anonymous Posted on May 16, 2014
Be the first to answer

Lakewood fan model hv18 power switch

The switch is broken. Do you have replacement switch

Answer This Question

4 Related Answers

David Shaub

  • 2994 Answers
  • Posted on Jul 26, 2009

SOURCE: have a lakewood shop fan pedestal type with 3

The switch has numbers on it. Mark the wires. Just connect the new switch the same way.

Ad
MOTORWIZJ

Jay Finke

  • 1397 Answers
  • Posted on May 28, 2010

SOURCE: I need a replacement motor, 60 HZ 2.7 amp, for a

GRAINGER.COM ... .GOOD LUCK AND I'FN I WAS ANY HELP PRAISE IS APPRECIATED .. SO VOTE JAY MOTORWIZJ

motor1258

Mike Butler

  • 6674 Answers
  • Posted on Jul 10, 2010

SOURCE: switch broken

May not be identical but an appliance store or hardware store should be able to assist you with that. Home depot or Lowes as well. Take old one with you if you can.

Anonymous

  • 1970 Answers
  • Posted on Jul 28, 2010

SOURCE: are replacement motors available for these fans?

mcdevito75 here, If the fan is not too old I would figure yes, but a replacement motor will cost as a new fan, if not more, then you have to install and the blades are a presss fit to the motor.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I needs a knob for 4 position 3 speed rotary switch. Lakewood 20" Kool Operator floor fan.
There is nothing specific to that model. You can however buy generic plastic knobs like these.

https://www.google.com/search?sca_esv=565418613&rlz=1C1QJDB_enCA643CA644&sxsrf=AM9HkKlfaPQxv5j_ZmPBay8QTshDeuhnNw:1694736820267&q=floor+fan+replacement+knob&tbm=isch&source=lnms&sa=X&ved=2ahUKEwj5kqPRqquBAxWZjokEHQB1DcgQ0pQJegQIChAB&biw=1920&bih=931&dpr=1

https://www.google.com/search?q=Lakewood+20%22+Kool+Operator+floor+fan+replacement+knob

..
Read full answer
Sep 14, 2023 • Rotary Computers & Internet
0helpful
1answer

Where can i get a lakewood fan motor for lakewood fan model number HV-18
you would have to go to a place that sells motors and get one by motor type, that than the appliance make and model. All electric motors are standard by size, voltage, speed and fixings.

https://www.google.com/search?q=lakewood+hv+18+replacement+parts

...
Read full answer
Jul 01, 2022 • Lakewood Dryers
0helpful
1answer

Mains Cord for Lakewood fan model LBF 2010A
Nothing specific to that fan, but they are all standard types. Pick the one that fits

https://www.google.com/search?q=power+cord+types

..
Read full answer
Jun 30, 2021 • Lakewood Dryers
0helpful
1answer

I am replacing the 4 position 3 speed rotary switch with knob on a Lakewood Kool Operator 20" floor fan. Do I just pull the wires out of the broken switch and push them into the new switch?
MANY OF THEM YOU NEED TO USE A PIN PICK TO RELEASE THE WIRE SLIDE IT ALONG THE WIRE WHERE IT ENTERS
Read full answer
Sep 06, 2020 • Lakewood Dryers
0answers

I need a 2 speed switch for a Lakewood fan RO Smith 1/4 hp motor model F48F71B82.
Read full answer
Be the first to answer Apr 01, 2018 • Lakewood Dryers
0helpful
1answer

Switch broken
May not be identical but an appliance store or hardware store should be able to assist you with that. Home depot or Lowes as well. Take old one with you if you can.
Read full answer
Jul 10, 2010 • Lakewood 200I Floor / Box Fan
4helpful
1answer

My lakewood HV18 just stopped. Spinning the shaft
I think you need to buy a new fan. Unless this thing cost several hundred dollars it isn't worth rewinding and a capacitor isn't likely to cause it to stop working, the cap is for STARTING it spinning anyway and sometimes they are used to HELP it run better, but it will try to run if you spin it and since your's does nothing, more than likely the windings are gone.
Read full answer
Sep 09, 2009 • Lakewood HV 18-c Floor / Box Fan
0helpful
1answer

Have a lakewood shop fan pedestal type with 3 blades and the switch is bad looking for diagram to replace the switch
The switch has numbers on it. Mark the wires. Just connect the new switch the same way.
Read full answer
Jul 26, 2009 • Lakewood HV-30PB Stand (Pedestal) Fan
1helpful
1answer

Need to replace the switch that has ,hi,low,med off on nit? please Help
you have 3 control wires (the 3 speeds) and a common wire. the common wire will go directly from the fan motor to the power source/cord and the other 3 leads will run through the switch. you could even use a standard dimmer-style lighting rheostat and connect it to the common and "high" fan speed wire and have infinitely variable fan speeds. hope that helps.
Read full answer
Apr 30, 2009 • Lakewood HV-18 Floor / Box Fan
0helpful
1answer

Power switches
what do the switches look like? can you supply a picture?
Read full answer
Nov 10, 2006 • Lakewood 7101 Oil Filled Radiator Heater
Not finding what you are looking for?

View Most Popular

HV 18-c Floor / Box Fan

  • Dryers

Related Question

I needs a knob for 4 position 3 speed rotary switch. Lakewood 20" Kool Operator floor fan.

  • Rotary Computers & Internet

134 views

Ask a Question

Usually answered in minutes!

Popular Questions

MC42 Replacement Fan Motor Part Number

Lakewood MC-42 Fan

Are replacement motors available for these fans?

Lakewood HV-18 Floor / Box Fan

My Lakewood box fan fell over and stopped working

Lakewood 200I Floor / Box Fan

Lakewood HV-18 fan... how to wire switch?

Lakewood HV 18-c Floor / Box Fan

Does the lakewood fan have a fuse that can be

Lakewood HV 18-c Floor / Box Fan

Top Lakewood Dryers Experts

Jay Finke
Jay Finke

Level 3 Expert

1397 Answers

Larry Ng
Larry Ng

Level 3 Expert

14591 Answers

ADMIN Eric
ADMIN Eric

Level 3 Expert

39386 Answers

Are you a Lakewood Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Lakewood fan manual.pdf....

HV 18-c Floor / Box...

Loading...