How to operate alarm

There isn't a valet switch but you should have a second valet key. That is designed to allow the car to be started and run but will not unlock the trunk or glove box. See if you have a key that is similar but not the same as the other main key and see if you can start it with that. If you have an remote alarm system, that could be interfering with starting. See if you can override the alarm.

you may check the fuse of your car,if you are not fixed the set belt may alarm again or in short you're fasten your set belt.and the other one your door not to much close,and you can cut off the wiring's of alarm.and that's the last option.

Hello

Sure Alarm battery Back-Up System

This SmartSet® Clock Radio includes a Sure Alarm battery back-up circuit that can

wake you up even if the power is 'Off'at the selected wake up time. If your power

is 'Off'at the selected wake up time the clock display will be off and the radio will

not operate, but a separate mini-buzzer will turn 'On'automatically to wake you up,

even if you had selected the "Wake to Radio"option.

The Sure Alarm will sound for 30 seconds and then shut off automatically.

To stop the Sure Alarm buzzer immediately, press the RADIO ON/OFF button.

Pressing the SNOOZE button has no effect during Sure Alarm operation.

Note: In order to maximize the life of the built in lithium battery, please be sure

to set the ALARM 1 and ALARM 2 switches to the "OFF"position if the radio

will be disconnected from the AC outlet for more than a few hours. This will
prevent the Sure Alarm from turning 'On'unnecessarily.

1.) Depress and hold either the ALARM 1 or ALARM 2 setting button.

The display will change from the correct time
to the Alarm 1 or Alarm 2 wake up time.

2.) While holding the ALARM 1 or ALARM 2 setting button, depress either the

SET + or - button to move the display ahead or back to your desired wake up
time.

3.) When the desired wake up time appears on the display, release the SET + or

- buttons.

Note: Be sure that you have set the wake up time correctly by observing

the AM indicator. If the AM indicator is 'On'the wake up time is "AM". If the
AM indicator is 'Off', the wake up time is "PM".

4.) When the desired wake up time (AM or PM) appears on the display, release
the ALARM 1 or ALARM 2 setting buttons

The hour and minute hands can be pushed onto their respective shafts at any point in most clocks.
If you already know the time that the alarm is set, let the clock run until it sounds.
When the alarm sounds, install the hour hand and the minute hand to the exact alarm set time. If, say, the alarm is set for 6:30, push the hour hand onto it's shaft at exactly half way between 6 and 7 and then push the minute hand onto it's shaft pointing at exactly 6.
I think this should get you operating.
Gary

Idle circuit of the carburetor is clogged or restricted. Clean the carburetor.

have a look at the manual and check how to disable the radio alarm to maximum range.as i think you have set it to automatic maximum volume.

good morning ! your anadigi chronograph 388 is veery easy to operate,just change the battery then short the reset button the fix the case back and set the time use the crown and the button to set the time calendar and the alarm !thank you ! god bless !....

Hi gidgid.
This is direct from manual mailed to me from Oregon Scientific re my own contrast problem.
1. Press [ALARM] to switch to display the alarm setting.
2. Select ALARM 1 or ALARM 2 using [ALARM].
3. Press and hold [ALARM] for two seconds.
4. Use VOLUME [ + ] / [ - ] to enter the hours.
5. Press [ALARM].
6. Use VOLUME [ + ] / [ - ] to enter the minutes.
7. Press [ALARM].
8. Use VOLUME [ + ] / [ - ] to select ALARM or RADIO. If
ALARM is selected, a two-minute crescendo alarm will be
emitted at the set time when the alarm is active. If RADIO is
chosen, the radio will be turned on for two hours at the set time
instead.
9. If RADIO is chosen, use [STATION] to choose the radio
station and press [AM / FM] to select AM or FM.
10. Press [ALARM].
11.Use VOLUME [ + ] / [ - ] to set the volume of the wake up radio.
12. Press [ALARM] to exit.
Note: If there is no battery for the radio, there is no operation for
step 9 ~ 11.
sleepy head

to change the alarm mode setting for alarm 1, hold alm1 setting button and press the alarm mode button until the day indicators show thedesired mode setting. weekday only,weekends only,or everday operation. release the alarm mode and alm 1 setting buttons and the display will return to correct time.

The 'mazda' setting is supposed to look like an analog clock, and that's for setting the time. The key position puts the clock in operating mode, as opposed to clock set or alarm set modes.

I've only had the clock for a day, but if you want the alarms to shut off and alarm again the next day, use the OFF switch on the top right of the unit. If you want to disable the alarms completely, use the 1 and 2 buttons behind the OFF switch to cycle each alarm through the settings: none, bell, music (radio)