At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I cannot login to my router, it's a WBR 1310. I type in the default "adim" without a password and it goes back to the login screen. I would like to set up a password to log on to the wi-fi.
Leave the username blank, then enter "admin" as the password. You can also reset the router to factory defaults by pressing the reset button on the back (small hole, use paper clip) and then try again.
reseting your router should work, according to the manual the username must be left blank and the default password is admin. Make sure you fully press the reset button while the router is powered on and keep pressing the reset button for at least 30 seconds. Please try reseting the router again and let us know. Good Luck!reseting your router should work, according to the manual the username must be left blank and the default password is admin. Make sure you fully press the reset button while the router is powered on and keep pressing the reset button for at least 30 seconds. Please try reseting the router again and let us know. Good Luck!
On another note, some routers have another method of reset which will bypass any problems.
Try this
Unplug the power from the router With the router powered off start pressing the reset button Keep pressing the reset button while you power back on the router (do not release the reset button) Mainting pressure on the reset button for at least 30 secs after you powered it back on Let the router finish the restar process and try to login again.On another note, some routers have another method of reset which will bypass any problems.
Try this
Unplug the power from the router
With the router powered off start pressing the reset button
Keep pressing the reset button while you power back on the router (do not release the reset button)
Mainting pressure on the reset button for at least 30 secs after you powered it back on
Let the router finish the restar process and try to login again.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If you already tried with username = admin password = blank "no
password at all" or password = "password" then the only way to recover
the router will be by doing a hard resset, (pressing the resset button
in the back for 12 seconds) be careful you are going to set the router
back to factory default and you will need to configure it again usually
this is the only way to get the router back
if you know the current password to the router please login to it by going to
http://192.168.0.1
if you dont the default login/password is admin/admin
once you login go to the tools link
below you can change the password.
if you want to change the wireless network password go to
setup>wireless settings
and change the security password there.
Yes you can - If you do not know the login and password - You
can reset the D-Link back to the factory defaults by - power off the D-Link,
press and hold the RESET button on the back of the router, then power up the
router. Hold the RESET button for 5 secs and release the RESET button or until
the LEDs flash together. Connect a LAN cable from the D-Link to the LAN port
on your computer and open a browser. Enter the D-Link's configuration URL
http://192.168.0.1 The default login = admin The default PW = blank (just
press Enter) You can now configure the wireless settings, eg. SSID and encryption etc.
You can follow these steps in enabling wireless security on your router and do this steps using a computer wired to the router since once you save the settings your wireless network will be secure.<br /><br />1) Open the internet browser and type the address 192.168.0.1 to login to the router. The default username is "admin" and leave the password box empty.<br />2) Click "Wireless Settings" on the left side.<br />3) Select the Security Mode ,Enable WEP Security.<br />4) Select the Authentication ,Shared Key.<br />5) Select the WEP Encryption , either 64-bit or 128-bit.<br />6) Select the Key Type ,HEX (only A-F and 0-9 number allowed) or ASCII (all number and character allowed).<br />7) Enter a WEP key as your security password to login to your wireless later.<br />8) Press Save Settings to save all settings changed. Reboot the router.<br /><br />
To access the router config screen, use a browser type in the address bar 192.168.0.1 login is admin and the password is blank hit enter. search the wireless screen for the enable button. Or you could reset back to default by (with the power on) stick a paperclip in the small hole by the power cord and hold it in for 10 to 15 seconds. the router will reboot back to default, and you can input your settings.
You need to log into the router setup screen - you do this by connecting a PC to the Router via a cable connection and then using Internet Explorer (IE) you log into the router.
Using the default settings
Open a web browser and enter http://192.168.0.1 and press Enter. When the login window appears, set the user name to admin and leave the password box empty. Click OK to continue.
Goto the Wireless security section to set the security type and the password
Section 4 of the manual - see below deals with setting the wireless security
This is the support site for that router http://www.dlink.com/products/?pid=WBR-1310
Click on the Support Resources - that will take you to the manuals for different Version of that model - click on the model you have to get to the online manual
Disable firewall on your computer. It seems that it's blocking you from getting in the setup page. you may also try using another computer to login just to isolate your problem
Go the router setup page, 192.168.0.1, type admin as the user name and password as the password (default, if you have changed these use your login info).
Then on the wireless page change the SSID (router name).
You can also add a security key on this page.
Click on this link or copy and paste the complete link into your browser. If I could be of further assistance, let me know. If this helps or solves the issue, please rate it. Thanks, Joe
anything else? Neither ideas are working...
×