What is error code 093 329 on a xerox color c75 press ?

Question edited for clarity.
Please don't type in all CAPS, it is considered SHOUTING which is rude and it makes it harder to read. Lower case additions are mine!

You need a service call

Error code 045 315 - Customer Support Forum

https://forum.support.xerox.com > Hardware > Error-co...
Nov 29, 2021 · 2 posts
Please take a look at this article about the Fault Code 045-315 in the online support for your machine. Please consider contacting your support ...

• 
  

  Fault Code 045-315: Video Line M Fault - Support - Xerox

  https://www.support.xerox.com > en-us > article
  Sept 21, 2015 - Fault Code 045-315: Video Line M Fault · Try these solutions · Did this help?

Error Code 045-315 - Copytechnet

https://www.copytechnet.com > ... > Xerox
Oct 18, 2019 - Check, replace Y M Ros unit. Or replace bad MCU pwb.
Xerox 700 error code 045-315
Sept 8, 2019
xerox 700 error code 045-316
May 31, 2019
Error Code Xerox 700 Fault Code 045-360
Sept 25, 2017
Xerox 700 Help please
May 20, 2017
More results from www.copytechnet.com

Xerox 700 color press error 045-315 - Color Printing Forum

https://www.colorprintingforum.com > threads > xerox-...
Aug 17, 2013 - I believe that error is referenced as being a YM (yellow/magenta) ROS assembly fault. This is the black box laser mirror assembly. xfactor ...

Try this link:

https://www.support.xerox.com/en-us/article/en/1048969

https://www.support.xerox.com/en-us/article/en/1050212

Tres posibilidades.

https://tr translate.google.com para trasducir a espanol

https://forum.support.xerox.com/t5/Community-Suggestion-Box/Xerox-Fault-Codes/td-p/17168

https://mans.io/files/viewer/344228/219

https://www.scribd.com/document/328638143/Xerox-c75-Press-Manual

https://www.google.com to search for more information.

Try this:
Enter Service mode:
1. On the Control Panel, press the Down Arrow button to select
Troubleshooting and then press OK.
2. Press the Down Arrow button to select Service Tools, and then press
OK.
3. While pressing and holding down the Up Arrow button, press the Down
Arrow button to display the Hidden Service Menu.

Select Reset Error Log
Reboot the machine? Yes
Wait for about 15 min.
Should be all right after that.

Last time did work just fine for me!
If don't work mail me at:
[email protected] or
[email protected]

And we try something else.

You controller is bad. C75 is "Redundant strobes on logic board are not the same."

Oven repair in Santa Ana, CA
Appliance repair in Santa Ana, CA

9-357 Black Toner Dispenser Broken.

Performing a Fault Reset 14 will reset your copier and will help to clear error codes.

1. Turn the power off.
2. Locate the Clear Button, which is grey in color, in the upper right corner above the green Start Button.
3. Locate the Auto Button the lower left corner of the Control Panel.
4. Turn the power back on.
5. Press the buttons in the following sequence, releasing each button after each time you press it: [Clear], [Auto], [Clear], [Auto]. Every light on the Control Panel should go out, and the error code should clear.
6. If the error code has not cleared, wait a few seconds then repeat Steps 1 through 5.
7. Program the copier as if you were going to make 14 copies.
8. Press the green [Start] button to store the reset code. The copier will return to the ready position.
9. Run a test copy.

Sorry I am not familiar with this machine, usually if you press the start key for 3 sec it should show you the other codes? Good luck.

P.S.: If i run into anything I'll send it to you .

Hello sir; The problem you have can be reset, just follow the steps as below;
1, power on the machine.
2, while hold down the 0 key, press start.
3, enter the access number 6789
4, click onNVM reset/NVM initialization.
5, enter 777-018 press start.
if still have problem let me know