Singer touch n sew 750 winding bobbins

If the needle on your Singer Quilter Confidence machine moves when you're winding the bobbin, it's likely due to a few possible reasons. Here are some steps you can take to resolve this issue:

1. Check the threading: Make sure the thread is properly threaded through the machine, as an incorrect threading can cause the needle to move during bobbin winding.
2. Tighten the needle clamp screw: If the needle clamp screw is loose, it can cause the needle to vibrate during bobbin winding. To tighten the screw, use a screwdriver to turn the screw clockwise.
3. Check the bobbin winder tension: If the bobbin winder tension is too loose, it can cause the needle to move. To adjust the tension, refer to the manual for your Singer Quilter Confidence machine.
4. Check for any obstructions: Make sure there are no obstructions near the needle, such as thread tails, fabric, or lint, as these can cause the needle to move during bobbin winding.

If you've tried all of these steps and the needle continues to move during bobbin winding, it may be a mechanical issue that requires a professional to fix. I would recommend contacting Singer for further assistance.

Do you mean the Singer 4411 Heavy Duty sewing machine? If so,
first place the spool on the spool pin with an appropriate sized spool holder, if you are starting the project. Snap the thread into the thread guide to the left of the of the spool pin. Wrap the thread clockwise around the bobbin winder tension discs (slightly to the left and forward of the thread guide). Bring thread towards the bobbin spindle. Thread the bobbin (put the thread through the hole in the bobbin). Place the bobbin on the spindle with the hole up. Move the bobbin spindle to the right. Hold onto the thread above the bobbin and step on the foot control pedal. When the bobbin finishes winding the thread, cut the thread at the top of the bobbin and the incoming thread from the spool. Move the bobbin spindle to the left and remove the bobbin. If you have already threaded the machine for sewing, you will need to remove it from the various guides and tension discs that are used in sewing. Then after winding the bobbin, re-thread the top thread.

The directions to wind the bobbin are in the manual on page 12 (page 19 of the PDF). You can find many Singer manuals at the Singer support page: https://www.singer.com/support . The 4411 support page is https://www.singer.com/search/support?lp=support&title=4411 . The current link to the manual is https://www.singer.com/sites/default/files/product_manual/SINGER%204411%20Heavy%20Duty%20Sewing%20Machine.pdf .

I hope this helps.

Cindy Wells

Perhaps this video will help:

Singer touch and sew bobbin threading

If it still will not wind, pick up a standalone bobbin winder for ~$30 from the local fabric store or online. One brand is called "Sidewinder." Be sure to check that it will accept your Singer bobbins!!!!

...

try this link for instructions on winding a bobbin

Winding Bobbin

http://www.ehow.com/how_7373026_use-singer-self_winding-bobbin.html


Winding Singer Sewing Machine Bobbin

Hai, Please change the new bobbin winder. Because bobbin winder and winding is very important.

Recheck the top thread and bobbin tension for equal balance of thread when sewing. The knotting of thread problem is usually because the tensions are too tight or too loose and/or thread may not be properly threaded. Another reason is when the bobbin thread is wind imbalanced it will cause the thread to knot-up when sewing. This problem is notorious when the bobbin is winded within the bobbin case on some machines. The bobbin thread need to be wind smoothly in the bobbin to avoid this problem.

It should not affect the winding, the reason the needle is still going up and down is because the oil has gone dry on the shaft and unless you can get to the shaft where the balance wheel is then it would be wise to take the machine in for a service, loose stitching on the bottom is a tension problem, make sure the top tension is set about 4 or 5

how to wind the bobbin of the singer touch and sew model 625

It sounds like you don't have any tension on the thread when winding the bobbin. Make sure that you are running the thread through the tension disc on the top of the machine before going to the bobbin winder.

Needle Faces Where?  
I Need to Tighten the Tension....  
Changing a Needle  
Need Help  
Basic Questions-  
Bobbin Assembly Popped Out!  
Do You Think My Machine is Fixable?  
How to Change a Broken Needle  
Needle Bar Adjustment  
Oiling an Elna 3007  
Getting the Timing Belt Off?  
What Size Needles for My Machine?  
How to Oil my Machine?  
Where to Oil??  
Stitch Length Knob Woes  
Can't Seem to Put the Bobbin in Correctly  
Timing Belt Tension  
Adjustments  
Running Very Slow-  
Oiling Points on Singer 257  
Oiling My Singer Touch & Sew  
Singer 457  
Featherweight Case Odor  
Brother XL2010 Q's  
Does My Machine Have More Than One Belt?  
Cannot Seem To Adjust the Tension  
What to Do About a Gumming Up Needle  
How Tighten My Bobbin Tension, Please  
Is it Covered Under Warranty?  
Proper Threading Instructions?  
Just a Foot Pedal?  
Simple Threading Instructions for a 1036  
Threading a Singer 600  
Replacing a Blade on a Johnson Ruffler  
Changing the Needle  
Lubricating a Singer 1036  
Thread Balling Underneath  
Warranty Info  
Machine Covered in Hardened Oil  
Spindle Stuck?  
Do Motors Die?  
Singer 457  
Brother Sewing Machine  
Servicing My Machine-  
Belt Replacement  
Lubricating My Sewing Machine  

check out this. good luck. thanks.