Hoveround mpv4 does not work led flash when turned on. 3 red 4 yellow and 1 green leds. the brakes, motors and wires have all been tested and work. Any Ideas?

1. VR2/VSI DIAGNOSTIC FLASH CODES

# OF LEDS
CODE
CAUSE
POSSIBLE SOLUTION
One red LED
1
Low battery voltage
Charge batteries
Two red LEDs
2
Left motor open
Make sure left motor is plugged into controller.
Three red LEDs
3
Left motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs One yellow LED
4
Right motor open
Make sure right motor is plugged into controller.
Three red LEDs Two yellow LEDs
5
Right motor wiring fault
Contact your authorized Pride Provider.
Three red LEDs Three yellow LEDs
6
Inhibit active
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs
7
Joystick error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs One green LED
8
Controller error
Contact your authorized Pride Provider.
Three red LEDs Four yellow LEDs Two green LEDs
9
Brake fault
Make sure both motors are plugged into controller.
Three red LEDs Four yellow LEDs Three green LEDs
10
High battery voltage
Contact your authorized Pride Provider.
What if the speed LEDs on the VR2/VSI begin to flash?

• Determine if the battery charger is connected to the power base. When the battery charger is connected to the power base, a charger inhibit feature keeps the power chair from driving. This is indicated by the VR2/VSI speed
  LED(s) flashing.
• Determine if the charger harness fuse has blown. A blown charger fuse can cause the charger inhibit to
  activate.
• Determine if all controller connections are plugged into the power base properly. If the 3-pin charger
  inhibit connector is not plugged in properly, then the charger inhibit feature will activate.

Fixtures are covered by Lithonia Lighting 24-month warranty against mechanical defects in manufacture.
All life safety equipment, including emergency lighting for path of egress must be maintained, serviced, and
tested in accordance with all National Fire Protection Association (NFPA) and local codes. Failure to perform the
required maintenance, service, or testing could jeopardize the safety of occupants and will void all warranties.
Note: Specifiations subject to change without notice.
Actual performance may diffr as a result of end-user environment and application.
Standard
Catalog Supply Input Pallet Carton
Number UPC Description Voltage Wattage Qty. Qty.
ECR LED M6 784231874516 Red 120/277 3.8 108 6
ECG LED M6 784231874592 Green 120/277 3.2 108 6
ECR LED HO M6 784231874561 Red, high output 120/277 3.8 108 6
ECG LED HO M6 784231874615 Green, high output 120/277 3.2 108 6
Accessories: Order as separate catalog number.
ELA WG3 Wireguard (back mount only) 1
ELA LED M12 Single remote lamp2,3
ELA LED T M12 Double remote lamp2,3
ELA LED WP M12 Single, weather-proof remote lamp2,3
ELA LED T WP M12 Double, weather-proof remote lamp2,3
Notes
1 See spec sheet ELA-WG.
2 See spec sheet LED-Remote Lamps.
3 Only available with HO option.
11 5/8 "
7 3/16 "
1 5/8 "
Integrated Exit-Unit Combo
12-5/8"
(32.1)
8"
(20.3)
4-3/8"
(11.1)
5-3/8"
(13.7)
1-7/8"
(4.8)
LED Unit
LED Combo
LED Exit
15 (38.1)
3-3/4
(9.5)
5-3/8 (13.7)
12 (30.5)
3-3/4
(9.5)
2
(5.1)
2"
(5.2)
4-1/2"
(11.4)
9"
(22.9) 8"
(20.3)
20"
(50.8)
12"
(30.5)
All dimensions are inches (centimeters).
Shipping weight: 3.6 lbs. (1.6 kgs.).
ECR LE

Check your battery connections, make absolutely sure it is connected correctly.

Place a multimeter in the XLR plug (joystick). You should have around 26V reading if batteries are connected correctly.

Check the free wheel levers. place the chair in free wheel and move back and forth a couple of times. Place the chair back into drive, turn on controller and try to drive. ( This is not typically associated with a clicking sound but will ensure your brakes are not on)

If you are still hearing a clicking sound, it could be a problem with the brake or a motor. A qualified technician should really look at it for you.

hope this helps

6 pin socket

6 pin plug

7 pin socket

7 pin plug

5 pin socket

5 pin plug

7 pin socket

7 pin plug

7 pin socket

7 pin plug

7 pin socket

7 pin plug

12 pin socket

12 pin plug

small 6 pin round plug & socket

1 tail, clearance - brown

2 left hand turn - yellow

3 right hand turn - green

4 stop - red

5 electric brakes - blue

6 earth - white

small 7 pin round plug & socket

1 left hand turn - yellow

2 reverse - black

3 earth - white

4 right hand turn - green

5 electric brakes - blue

6 stop - red

7 tail, clearance, side markers - brown

round socket

large 5 pin round plug & socket

2 left hand turn - yellow

3 earth - white

5 right hand turn - green

6 stop - red

7 tail, clearance, side markers - brown

large 7 pin round plug & socket

1 left hand turn - yellow

2 reverse - black

3 earth - white

4 right hand turn - green

5 electric brakes - blue

6 stop - red

7 tail, clearance, side markers - brown

7 pin round heavy duty plug & socket

1 earth - white

2 left hand rear , clearance and marker - black

3 left hand turn - yellow

4 stop - red

5 right hand turn - green

6 right hand rear , clearance and marker - brown

7 reverse/auxilary - blue

7 pin flat plug & socket

1 left hand turn - yellow

2 reverse - black

3 earth - white

4 right hand turn - green

5 electric brakes - blue

6 stop - red

7 tail, clearance, side markers - brown

flat socket

12 pin flat plug & socket

1 left hand turn - yellow

2 reverse - black

3 earth - white

4 right hand turn - green

5 electric brakes - blue

6 stop - red

7 tail, clearance, side markers - brown

8 battery supply - orange

9 auxiliaries - pink

10 earth - white

11 rear fog lamp - grey

12 auxiliaries - violet

According to my 1170 manual the flashing lights are error codes. 1 red = low batt., 2 red = left motor disconnected, 3 red = Left motor wiring fault, 4 yellow = Right motor disconnected, 5 yellow = right motor wiring fault, 6 yellow = Inhibit active, 7 yellow =possible joystick fault, 8 green = possible controller fault, 9 green = Solenoid brake fault, 10 green = high batt. voltage

rakoble the 9 flashes error code can indicate the brake lever not in drive mode or if you have the electric seat its not all the way down or finally a controller problem and on the Hoveround thats the joystick. Check the brake levers and the seat if you have that on your chair. If the first two are ok then its the joystick and you'll have to get a new one. Hope this helps

Hi there,

If you have the Renault end, I've got the rest. I have the pinouts for 7 wire, 6 Wire and 4 Wire, One of them will fit the bill

Plug Types/Application
7 Way - RV Trailers, Horse and Utility Trailers
6 Way - Horse, Stock and Utility
4 Way - Utility Trailers

Columns are: Color, Function, Mark on the plug.

Seven wire Trailer plugs:

Horse, stock or utility trailers:
White = Ground - 1
Blue = Electric Brakes - 2
Brown = Tail and clearance lights - 3
Black = Battery, aux power - 4
Yellow = Left turn/Brake - 5
Green = Right turn Brake - 6
Orange or Purple (not both) = Auxilliary or Reverse - 7

Recreational Vehicle:
White = Ground - 1
Blue = Electric Brakes - 2
Green = Tail and clearance lights - 3
Black = Battery, aux power - 4
Red = Left turn/Brake - 5
Brown = Right turn Brake - 6
Yellow = Auxilliary or Reverse - 7


Six wire trailer plugs:

Horse, stock or utility trailers:
White = Ground - GD
Yellow = Left turn/Brake -LT
Green = Right turn Brake -RT
Brown = Tail and clearance lights - TM
Red or Black (not both) = Battery, aux power - A
Blue = Electric Brakes - S

Recreational Vehicle: (color, use, plug mark)
White = Ground - GD
Brown = Right turn Brake - RT
Green = Tail and clearance lights -TM
Black = Battery, aux power - A
Red = Left turn/Brake - LT
Blue = Electric Brakes - S


Four wire plugs:
White = Ground
Yellow = Left turn/Brake
Green = Right turn Brake
Brown = Tail and clearance lights


Ground should be 10ga.
Others 14 ga

A test light and a 12VDC power source can be handy for trouble shooting
.
Best regards
Mike

Problem solved.

Typically Harley uses a red and a green wire on their tail light assemblies. The red wire is usually the brake light, green being the tail light.

Using a test light, turn the switch on, push the probe into the red wire, and step on the rear brake pedal. If the test light illuminates when you step on the brake pedal, you've got the right wire for the brake light. The green wire should be "hot" whenever the ignition switch is "on" and the headlight is on.

anti theft. while the lights are flashing, hit the horn button twice.