FGHD2433KF1 err eu

To me the Error is telling you Probe Error - Wash - Power - Drain

CL & CLe Series Dishwasher Display Codes Below are common codes that display on Hobart CL and Cle Series Dishwashers:

• Door(s) Open - This displays if one or both doors are open. Close all inspection doors.
• Clear Conveyor Jam - The code appears if there is a jam. Remove the rack from the machine. Then, press START and rerun the rack.
• Probe Err - TANK - Check if the lower float assembly in the displayed tank isn't visibly damaged and that the proper amount of water is covering the lower float in the tank.
• Probe Error - FnlRns - Make sure the supply water valve to the rinse booster is open.

More here and a video

https://www.google.com/search?q=Hobart+PROBE+ERROR-WASH+PW+DR

https://www.hobart.com.mx/pdf/FichaTec/F-40196.pdf

Service Manual

https://hvac-talk.com/vbb/attachment.php?s=219f76d9e796c2e5f1c5fef6b79fad9d&attachmentid=830275&d=1639784925

from here

https://hvac-talk.com/vbb/threads/2234701-Hobart-Service-Manuals

..

No you can't unless you are trained and have the repair manual.

Thank you for your post, Cathie Sanchez!

I understand that your Frigidaire dishwasher is displaying error code "S" and will not restart. The error code "S" usually stands for sanitize, this could also be a miscommunication within the control panel. I would recommend performing a reset on your dishwasher and you can do that by disconnecting power from your dishwasher for roughly ten minutes. If you continue to experience issues with the error code I would suggest having a professional technician out for proper diagnosis and repair. Hope this is helpful. -Matt

Hello friend, thank you for your post!

From my understanding the "S" stands for sanitize within your Frigidaire dishwasher. I hope this is helpful. If you have any additional questions please feel free to reconnect. -Matt

Hello Lou,
I see that your Frigidaire dishwasher will not start. I would recommend giving the appliance a hard reset. You will do this by switching the circuit breaker off that the dishwasher is attached to. When you do this you will want to leave it off for 20-30 minutes. Once the 20-30 minutes has elapsed, bring power back to the dishwasher and try to restart it. If you are still receiving a 125 error code and the dishwasher is not starting, I would suggest contacting your local authorized technician to diagnose and see why you keep receiving this error code.

-Best Regards-

rlindaur179,There are a couple possible issues. We will start with the easy ones first.
1. There is a round shape float on the inside floor of the dishwasher.On this mode I believe it is in the front left. please check to see this float moves easily up and down. If there is any build up it could getting stuck in the upright position this can cause a reset in the cycle. Clean the float shaft. Lift float and clean shaft (steel wool works well)2. Replace control board
Hope this helpsJoe Connolly

If you recently replaced the garbage disposal the dishwasher knockout has not been removed. OR the dishwasher drain hose is not high enough and water is leaking back in from the sink.

Your pump may be cracked or a drain hose may have a hole. Also check the dishwasher housing not the cabinet that you can see I have seen small holds due to defects in the plastic that the housing is made up of. Of time with heat and moisture these hols may appear. Look for small crackes in crevices. They are hard to detect once the cabinet is removed start the dishwasher and have flashlight to see exactly where water is coming from.

If you have anymore questions please comment me back.

It is in a delay wash mode.
Disconnect power for 60 seconds.
Re-connect power.
Press the Cancel button.
Press the regular wash cycle and start the dw.