Q2 pro set will not shut down

Hello Don;

My name is Peter. I am a retired field service refrigeration technician.

Your filter reset is just a independent timer set for six months. It is not tied into your water filter. You should change your water filter when your water dispenser flow is slow and/or you start to get small ice cubes. Depending on the usage, your water filter can last 18-24 months or more.

Unplug your unit for about 10 minutes to let the unit power down, then plug it back in.

follow this steps and fix it. God bless you

1. Main control boardIf your microwave runs for a few seconds and stops, the first thing to check is the main control board to ensure that a shortage has not occurred. If the part is defective then it will need to be replaced to prevent continual shut offs. If this is not the issue, the next step would be to check for a faulty touchpad.
   
2. Touchpad/Control panelIf the control board is not the issue and your microwave continues to shut off after running for only a few seconds, the next thing to check is your touchpad, which is also known as a control panel. Although uncommon for this issue, symptoms are usually that the display and some buttons are working properly; however, when selected some buttons are not functioning. If this is the case the touchpad will need to be replaced.
   

Read more: http://www.appliancepartspros.com/repair-help/microwave-repair-help.html#7#ixzz2hPnOVle4
http://www.appliancepartspros.com

First step would be to Reset Your Mac's SMC
The method for resetting your Mac's SMC depends on the type of Mac you have. All SMC reset instructions require shutting down your Mac first. If your Mac fails to shut down, try pressing and holding the power button until the Mac shuts down, which usually takes 10 seconds or so.

Mac portables with user-removable batteries (MacBook and most MacBook Pros):

1.Shut down your Mac.
2.Disconnect your Mac portable from its MagSafe connector.
3.Remove the battery.
4.Press and hold the power button for at least 5 seconds.
5.Release the power button.
6.Re-install the battery.
7.Reconnect the MagSafe connector.
8.Turn your Mac on.
Mac portables with non-user-removable batteries (MacBook Air and some late 2009 MacBook Pro models):

1.Shut down your Mac.
2.Connect the MagSafe power adapter to your Mac and to a power outlet.
3.On the built-in keyboard (this will not work from an external keyboard), simultaneously press and hold the left shift, control, and option keys while you press the power button. Release all keys at the same time.
4.Press the power button to start your Mac.

Mac desktops (Mac Pro, iMac, Mac mini):

1.Shut down your Mac.
2.Unplug your Mac's power cord.
3.Press and hold the Mac's power button for 15 seconds.
4.Release the power button.
5.Reconnect your Mac's power cord.
6.Wait five seconds.
7.Start your Mac by pressing the power button.

Alternative SMC reset for Mac Pro:

If you have a Mac Pro that isn't responding to the normal SMC reset as described above, you can force a manual SMC reset by using the SMC reset button located on the Mac Pro's motherboard.

1.Shut down your Mac.
2.Unplug the Mac's power cord.
3.Open the Mac Pro's side access panel.
4.Just below the Drive 4 sled and adjacent to the top PCI-e slot is a small button labeled SMC. Press and hold this button for 10 seconds.
5.Close the Mac Pro's side door.
6.Reconnect your Mac's power cord.
7.Wait five seconds.
8.Start your Mac by pressing the power button.
Now that you have reset the SMC on your Mac, it should be back to operating as you expect. If the SMC reset didn't fix your problems, you can try combining it with a PRAM reset. Although the PRAM works differently than the SMC, it can, depending on your Mac model, store a few bits of information that the SMC uses.

The grey screen is the bios of your laptop is booting, this is freezing for some reason.
Do 3 things.
Try holding power button down for longer at least 10-20 seconds.
do a PRAM reset, apple symbol, alt P & R keys all held on boot up.
Do a smc reset.

1. Shut down the computer.
2. Disconnect the MagSafe power adapter from the computer, if it's connected.
3. Remove the battery.
4. Press and hold the power button for 5 seconds.
5. Release the power button.
6. Reconnect the battery and MagSafe power adapter.
7. Press the power button to turn on the computer.

---

Please dont forget to vote this answer was helpful

Many thanks

------

Any bluetooth device should work with the iPhone4. Here is the directions for "pairing" from the BlueAnt website.

1. Make sure the Supertooth 3 is turned off. You can tell if the Supertooth 3 is on or off by looking at the light on the front. If the light is on or flashing, then the Supertooth 3 is on: turn it off by holding down the Multi-Function button (the green button) for about 5 seconds, until you hear the voice announce that the Supertooth 3 is powering down.
   
2. With the Supertooth 3 off, hold down the Multi-Function button for about 6 seconds, until the light on the front of the unit starts flashing red and blue.
3. The Supertooth 3 will now prompt you to select your language: press the Multi-Function button when you hear your language spoken.
4. The Supertooth 3 is now in pairing mode.

Pairing Your BlueAnt Step 4: Apple iPhone Now you need to use your iPhone to search for Bluetooth devices:

1. Select Settings.
2. Select General.
3. Select Bluetooth.
4. Wait for your phone to search for devices, then select your BlueAnt device from the list.
5. If you are prompted for a PIN, enter 0000 (four zeros).
6. Select Connect.

Your BlueAnt device is now paired.

Hello Gdemon6 Here is a step by step instruction on how to fix this issue.
Firstly turn off your playstation 3 controller, insert the USB cable into the playstation and then the controller. Have a small pin to hand, when its flashing press the button located at the back of the controller to the top, next to the screw hole. It is a very small hole, go to settings in your playstation 3 menu. Under accessory settings, go to recalibrate controller.
Your playstation 3 controller should now be ready to use properly without any issue. Any further questions please feel free to ask. Thanks for using fix ya.

To prevent children from accidently changing the

dishwasher cycle or starting the dishwasher, lock

the dishwasher controls by pressing and releasing

the DELAY START pad (some models) or the AIR

DRY pad (some models) for 3 seconds. An

indicator light on the lock graphic pad will illuminate

when the controls are locked and no new

selections can be made until the lock is released.

To unlock the controls, press the DELAY START

pad or AIR DRY pad until the indicator light goes
out

mcdevito75 here, Try to simply shut the monitor off at the monitor itself, Or with your computer shut down, disconnect and reconnect the monitor to the computer.

Hi,

To set the clock, do the following:
1. Press and hold the MULTI-CONTROL button for 2 seconds
2. Rotate MULTI-CONTROL button until display reads CLOCK.
3. Push MULTI-CONTROL button up or down to adjust hour and minutes.
4. Press ESCAPE or SOURCE button to exit

Remove the top cover and take a hair-dryer to the PC boards on the back of the main control panel.. (3 screws take the top cover off from the back) Mine has done it a total of 5 times now.. what it needs is all new buttons installed.. or a new control panel if this works..