Network and usb not selectable in setup menu

Hi Edward,

Here are the steps..

Internet Setup

Step 1: Enter Settings
Step 2: Select Wireless & Networks
Step 3: Select More...
Step 4: Select Mobile Networks
Step 5: Ensure Data Enabled is checked (enabled).
Step 6: Select Access Point Names
Step 7: Create a new APN (Select Menu, followed by New APN). Enter WIND Data as the name for the new APN. Under the headings APN enter internet.windmobile.ca (leave all other fields blank).
Step 8: Save the APN settings by selecting menu and then save.

Picture Messaging (MMS)

Step 1: Enter Settings
Step 2: Select Wireless & Networks
Step 3: Select More...
Step 4: Select Mobile Networks
Step 5: Ensure Data Enabled is checked (enabled).
Step 6: Select Access Point Names
Step 7: Create a new APN (Select Menu, followed by New APN). Enter WIND MMS as the name for the new APN. Under the following information in the listed headings:

• APN: mms.windmobile.ca
• MMSC:http://mms.windmobile.ca
• MMS Proxy: 74.115.197.70
• MMS Port: 8080
• MCC: 302
• MNC: 490
• APN Type: mms
• Leave all other fields blank.

Android 2.1 to 2.3

Internet setup

Step 1: Enter Settings
Step 2: Select Wireless & Networks
Step 3: Select Mobile Networks
Step 4: Ensure Data Enabled is checked (enabled).
Step 5: Select Access Point Names
Step 6: Create a new APN (Access Point). Enter any name you would like to call your internet connection and the access point as internet.windmobile.ca (leave all other fields blank).

Picture Messaging (MMS) setup

Step 1: Enter Settings
Step 2: Select Wireless & Networks
Step 3: Select Mobile Networks
Step 4: Ensure Data Enabled is checked (enabled).
Step 5: Select Access Point Names
Step 6: Create a new APN (Select Menu, followed by New APN). Enter WIND MMS as the name for the new APN. Under the following information in the listed headings:

• APN: mms.windmobile.ca
• MMSC: http://mms.windmobile.ca
• MMS Proxy: 74.115.197.70
• MMS Port: 8080
• MCC: 302
• MNC: 490
• APN Type: mms

2 ways to update Vizio BR vbr220, see page 41 of manual
1. via USB
2. via internet
Via USB
1. Download the software from www.vizio.com to the root directory of a USB thumb drive.
Notes:
The USB storage device should be 1GB or larger with at least 100MB of free space and
formatted FAT32. NTFS and other file systems are not supported.
The USB storage device must not have other .iso or .dat files in the root directory.
2. Connect the USB storage device to the USB port on the front of your player.
3. Follow the on-screen instructions to update your player.

Via Internet
When a new software update is available, a message will be displayed on the Home menu. To
update the software:
1. Connect your Blu-ray player to your home network
2. Press the B (green) button.
OR
a. Press < or > to select Settings and then press SELECT.
b. Press < or > to select System. The System menu opens.
c. Press \/ to select Update Via Network and then press SELECT.
3. Follow the on-screen instructions to update your player.

How to Update Toshiba TV Firmware

1. Plug a USB flash drive in to an available USB port on your computer and copy any files from the drive that you want to keep into a separate folder on your computer.
2. Format the drive as a FAT32 file system. This erases all of the files currently on the USB flash drive.
3. Click here to open the Toshiba Support home page.
4. Click "Product Support" in the menu along the top of the home page. The Product Support drop-down menu opens.
5. Select "Televisions" beneath Choose Category.
6. Select your type of Toshiba TV beneath Choose Family. For example, options include 3D TV, LCD TV and LED TV.
7. Select your Toshiba TV model beneath Choose Model.
8. Click the red "Go" button to the right of the Choose Model section after selecting your Toshiba TV model. The product support page for that specific TV model will be displayed.
9. Select the "Downloads" tab. If there are no downloads available for your TV model, either your won't be able to click the tab or there will be a message within the tab that says there are no downloads at this time. If this is the case, no firmware updates are available for your Toshiba TV. Check back periodically, as firmware updates are released as needed and aren't scheduled.
10. If there is content in the Downloads section, look in the Category section for an item titled TV Firmware. If this option doesn't appear, no firmware update is available. However, if this option does appear, click the clickable link associated with the firmware. The TV Firmware Update and Release Notes dialog box appears. In this dialog box you can see the size of the firmware update file, when it was released, exactly what it addresses and more.
11. Click the red "Download Now" button and save the file to your connected USB flash drive.
12. Extract the contents of the ZIP file on the USB flash drive.
13. Disconnect the USB flash drive from the computer after the firmware update file saves successfully to the device.
14. Power on the Toshiba TV and then connect the USB flash drive to the USB port on the Toshiba TV.
15. Wait a few moments for the "Firmware file is detected in USB" dialog box to appear on the screen. Select "Yes" to update the firmware. A progress bar displays on the screen. Be careful not to turn your TV off while the firmware is updating. The progress bar changes to a "Success!" message after the update successfully installs.
16. Disconnect the USB flash drive from the TV and then restart the TV. After the TV restarts you can resume using the TV as you normally would.

Confirming the firmware version:

1. Turn on the D80
2. Press the MENU button and select Firmware Version from the setup menu. The camera's firmware version will be displayed.
3. Turn off the D80

Basic Upgrade instructions: for detailed instructions, see pdf files below.

1. Download and expand the firmware files
2. Format an approved SD (Secure Digital) memory card in the camera
3. Connect Camera to computer (in MSC USB mode) or use a SD Card Reader
4. Copy to the top level of the card the downloaded "A firmware" file
5. Disconnect camera from computer
6. Update the firmware from the "Setup" menu
7. Follow the camera's on-screen menus
8. Repeat steps 2 through 7 using the "B Firmware"
9. Re-format Card

D80 1 11 firmware upgrade Nikon Knowledgebase

USB port may be only used to update the software in the tv. In setup menu, find the usb section. If it has a selection to up date and pictures, choose pictures. It will then find and display pictures stored on a thumb drive but will not show motion video

Download the latest BIOS update from your computer manufacturer's website onto a USB flash drive. Refer to your user manual to obtain the manufacturer's website address.

If the downloaded BIOS file is a zip archive, unzip the contents onto your USB flash drive.

Jumper settings may need to be reconfigured on some motherboards to enter BIOS recovery mode. Most Intel-based motherboards have a jumper setting or switch near the on-board

CMOS battery.

The procedure for setting the jumpers will vary depending on your motherboard make and model, so refer to the motherboard documentation for specific instructions.

Power on the computer and press "F2" to access the Setup Mode menu.

If you are unable to access the setup menu, you will not be able to proceed with this repair. Take your computer to a repair shop, as the motherboard may need to be replaced.

Use the arrow key to select "Boot Priority" or a similarly named field. Press the "Enter" key.

Scroll down until "First boot priority" or "First boot drive" is selected and press "Enter."

Select the USB flash drive as the first boot priority device. Press the "F10" key to save this setting and exit from the setup menu.

Connect the USB flash drive to an open USB port on your computer.

Then let your computer fully reboot.

The USB flash drive should be detected and the BIOS should update automatically.

When the update is complete, you may be prompted to restart your computer, or it may reboot automatically.

If you are able to use your computer without any further problems of overheating or failure to recognize drives, your failed BIOS update has been resolved.

hope this helps

Go HERE is the latest firmware and keep the router on to the setup page.Open the USB device manage and select updater.Or go to my computer, right click, select manage.This will open the device manager and then right click the USB adapter under network adapters and select update driver.Then select the last option from the menu and remember where is the file of the firmware so you can point the wizard to the file.

There is conflict between the Printer and Router you are using. The Router is freezing the printer connectivity to the network due to the Wireless radio ON option in the printer

There is a firmware update for your printer, Let your printer be connected thru USB and from this link, download and install the update for your printer and later try setting it up wireless, it should work.

http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-62339-2&lc=en&dlc=en&cc=us&os=2093&product=2512010&sw_lang=

If this step fails, the other step is, to Enter the printer IP Address manually in the printer Network menu from SEtup Option and later run the wireless setup wizard to connect it to the network.

Hi Friend,

Please follow the steps in order to resolve the issue:

1.Connect the wire (which is coming out from the modem) to the WAN/Internet port of the router.
2.Connect the computer to either of the four LAN ports of the router.
3.Turn on the router and press and hold the RESET button for 30 seconds and turn it off

for another 30 seconds and turn it ON.
4.Type 192.168.1.1 in the address bar of Internet Explorer and hit enter.
5.Leave the username blank and type admin in password.

If you have cable Internet connection then follow the steps:

6.In the setup page make sure that the Internet Connection Type is selected as Automatic
Configuration.
7.Click MAC Address Clone tab. Select Enable and click the tab CLONE. Click Save settings.

If you have DSL Internet connection then follow the steps after Step5:

6.In the setup page select PPPoE in the Internet Connection Type and enter the Username

and password provided by your Internet Service Provider. Click Save Settings.

In order to configure Wireless settings, please follow the steps:

7.Now click Wireless(to configure wireless) and fill the sections as mentioned

Wireless Network Mode:Mixed
Wireless Network Name:As per your choice
Wireless Channel-6-2.437GHz
Wireless SSID-Enabled and click Save Settings

8.Click Wireless Security and fill the sections as mentoned

Security Mode-WEP
WEP Encrypion-40/64 bits 10hex digits
Key1-Enter 10 digit password(e.g-your 10 digit telephone number) and click Save Settings

Also upgrade the Firmware of the router. You may visit the link in order to upgrade firmware

http://homesupport.cisco.com/en-us/wireless/linksys/

I hope this will resolve the issue.


Regards
Chiranjeet

please go to the web site below.
www.blu-ray.com/firmware/firmware.php?id=23 - 4 hours ago