Broken Power Switch

Hello Andrew

You didn't specify what you mean by "Broken"

Do you mean physically broken or
It just doesn't turn the tv on?
There are separate answers for each.

1:To fix a physically broken switch you could simply open the TV up and attach 2 wires to where the switch contacts are soldered to the PCB.
Run the wires to a new switch. Probably a NO (Normally Open) type. A Round switch could be mounted easily with a drill hole through an unused area of the case. Pressing a NO switch closes the contacts momentarily to trigger the digital turn On.

2:You could remove the old switch & attempt to get an actual replacement or a similar mountable switch from a components supplier.

3:If the switch is actually physically OK and the internal contacts are working (test with multimeter) then the problem is with the digital switch mode power supply that supplies power to the main circuits.

This would probably be caused by leaky Electrolytic Capacitors on the power supply PCB.
In that case, if your up to using a soldering iron and locating the Cap's then this would be an inexpensive way to fix the TV.

Good Luck
Switched mode power supply

Capacitor Replacement Tutorial
How to Replace an Electrolytic Capacitor

This is usually caused by either a bad door switch or a loose door switch mount, which are pretty simple problems to fix.

Even though a door switch clicks, it may still be bad inside.

Door switch or mount trouble is usually caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.



If the switch mount is broken, it's usually more economical and safer to add a dab or two of hot glue to the mount to secure the switch. Let it cool for about 30 minutes before using.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

Since this is posted under R-530BS, I'll assume that's your model number.

We have the service / repair manual for this model and have uploaded it to our site here for free download to help you.

If that's not your model, feel free to contact me directly with your model number.

If you only need a switch, you can order a universal type here for $5 postpaid.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

William E. Miller, AS-EET
[email protected]
http://www.microwavedisplay.com
Microwave Oven Control Panel Repair Nationwide

This is usually caused by either a bad door switch, a loose door switch mount (which are pretty simple problems to fix) or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside.

Door switch or mount trouble is usually caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.



If the switch mount is broken, it's usually more economical and safer to add a dab or two of hot glue to the mount to secure the switch. Let it cool for about 30 minutes before using.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

If you only need a switch, you can order a universal type here for $5 postpaid.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases with a one-year guarantee.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch, a loose door switch mount (which are pretty simple problems to fix - see this file) or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside.

Door switch or mount trouble is usually caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.



If the switch mount is broken, it's usually more economical and safer to add a dab or two of hot glue to the mount to secure the switch. Let it cool for about 30 minutes before using.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

You can find links to helpful exploded view diagrams and part ordering help here.

I recommend that you bookmark that link to your favorites.

There should be a "mini-manual" (tech sheet) hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting, testing, and locating components.



At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes.

If you don't find yours, or if you want to look at it without disassembling the oven, you can download it here.

If you only need a switch, you can order a universal type here for $5 postpaid.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases in about a week or so with a one-year guarantee.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch or a loose door switch mount, which are pretty simple problems to fix.

Even though a door switch clicks, it may still be bad inside.

Door switch or mount trouble is usually caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

If the switch mount is broken, it's usually more economical and safer to add a dab or two of hot glue to the mount to secure the switch. Let it cool for about 30 minutes before using.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

See these files:
http://www.microwavedisplay.com/safety.txt

http://www.microwavedisplay.com/disassembly.txt

http://www.microwavedisplay.com/doorsw.txt

At our Web site, we have a video available showing how to remove a typical over the range control panel assembly in under 5 minutes.

If you only need a switch, you can order a universal type here for $5 postpaid.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases in about a week or so.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch, a loose door switch mount (which are pretty simple problems to fix) or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

If you or someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa:.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

There may also be a "mini-manual" hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting & testing.

If you only need a switch, you can order one from us for $5 postpaid.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch, a loose door switch mount, or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

If you or someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa:.

You can find helpful exploded view diagrams and order parts by entering your full model number here.

Glad you found the "mini-manual". It's very helpful when troubleshooting & testing.

If you only need a switch, you can order one from us for $5 postpaid.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

When you hit Start, does the oven lamp come on but not the fan or turntable?

That would be a problem with the secondary (bottom) door interlock switch or its mount.

This is usually caused by either a bad door switch, a loose door switch mount, or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

If you or someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa:.

You can probably find exploded views and order parts by entering your model number here at the Sears parts site.

The best place to order Sharp parts is Tritronics.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch, a loose door switch mount, or occasionally a problem on the control panel.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. Other times, it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

One test that sometimes helps is to gently lift up (and/or push down) on the door or handle as you try to start it. If it works or tries to work, then it's a door switch mount or door alignment issue.

If you or someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa:.

You can probably find exploded views and order parts by entering your model number here at the Sears parts site.

There may also be a "mini-manual" hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting & testing.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases.

We're happy to help you and we'd appreciate your thoughtful rating of our answer.

This is usually caused by either a bad door switch, a loose door switch mount, or a problem on the control panel.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

There are plastic mounts inside the microwave which hold the door switches and onto which the door latches lock when you close the door.

The screws on these mounts may be loose. If they get too loose, the switches will not be activated properly.

Sometimes it's a broken tab on the switch holder, allowing the switch to rotate just out of position. Other times, it's a broken tab on the switch holder, allowing the switch to rotate just out of position. This tab can be hard to see, since it is under the bottom edge of the switch.

If you or someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa: http://tinyurl.com/yzjozk

You can find helpful exploded view diagrams and order parts by entering your full model number here: http://tinyurl.com/gv383

There should also be a "mini-manual" hidden inside the unit behind the control panel or hidden on the left side behind the grille, which is very helpful when troubleshooting & testing.

If you think the problem is on the control panel, we repair these nationwide by mail for $39.95 postpaid in most cases.

We're happy to help and we appreciate your thoughtful rating of our answer.