Console not working properly

The home button is not working. I have tried resetting it to see if that was it, but it turned on to a blank screen and then a few min later it shut off. I can't use the treadmill at all. No other buttons working either??? HELP!

5 Related Answers

Atlanta Fitness

23 Answers
Posted on Aug 24, 2009

SOURCE: Buttons doesn't work...

you more than likely need a new keypad
www.AtlantaFitnessRepair.com

Anonymous

40 Answers
Posted on Nov 01, 2009

SOURCE: Nordictrack motor will not run when start button is pushed.

Likely the cover of one of the motor brushes popped off. Unplug the machine before you pop it back in place, then try it again.

If that doesn't work, most likely it's the motor control board, or possibly the console, or finally just a loose connection behind the console.

But most likely, it's the motor brush cover. I've been seeing that alot with this model.

ernesto cuadra

12223 Answers
Posted on Nov 17, 2011

SOURCE: Nordictrack COmmercial 1500 console buttons don't work

http://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnes

sincerely. Please keep me in touch.

ernesto cuadra

12223 Answers
Posted on Nov 21, 2011

SOURCE: Treadmill won't start. Console works but when

If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console
. Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk.
Remember the Display Console Board has circuit that send to PController Motor, and after you did the adjustment you can conclude if the Sensor Reeed is faulty, 2) The Display of 3) The main Controller Motor.

Anonymous

1 Answer
Posted on Nov 16, 2012

SOURCE: nordic track exp 1000 treadmill console

Hii sumazone, was just wondering if you ever found out what was wrong?? I am havng same problem. thank you

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Siri keeps asking "Which setting' What setting should I say?

Never happened to me, but try reseting the phone. You do this by turning the phone off and then back on again but hold the home button while turning it back on. If this doesn't work, you might have to take your phone to a repair center.

Read full answer

Oct 07, 2014 • Apple iPhone Cell Phones

tip

Display problems while playing Virtual Console games

If you are experiencing display issues (dim, blank or half-blank screen, ghosted image, etc.) with a Virtual Console game while using the Component Video Cable, please read the following:
Some Virtual Console games default to displaying 240 lines of video. Some HD TV's are unable to display a signal with only 240 lines. Try the steps below to set the Wii to output 480 lines of video, which may solve the problem:

While on the Wii Channel Menu (main screen of the Wii), connect a Nunchuk to Wii Remote.
Select the Virtual Console game from the Wii menu, then select "Start" to begin the game.
When the game starts, press the Home button on the Wii Remote. (In many games, the music can be heard when the game starts.)
Select "Operations Manual" from the Home menu.
Press the Z + A + 2 Button simultaneously (the Z Button is on the Nunchuk). A sound will be heard if the button combination has been entered correctly.
Close the Home menu. The game should now display correctly. Note: You will not have to do this the next time you play, as the Wii console will remember these settings.

If the Virtual Console game is still not displaying properly, but all other games work fine, please call 1-800-255-3700 so that we may assist you further.

Read full tip

on Mar 04, 2010 • Video Game Consoles & Games

0helpful

2answers

Ipad has voice over only when turned on..blank screen

Triple click the home button. Then double tap the VoiceOver off button. This should allow the device to return to normal operation. Then you can reset by pressing and holding both buttons (power and home) until it resets if you need to.

Read full answer

Aug 23, 2014 • Apple iPad 32 GB WiFi Tablet PC

0helpful

1answer

My PS3 Turns on. The green light turns on but when i turn it to the right HDMI the screen is blank.

Hello,

This sounds like a cable problem. If you're going through a home theater receiver, try plugging it directly into the TV. If it works then it sounds like your home theater box needs to be tuned properly. If it doesn't work, then try replacing the HDMI Cable.
Failing that it could be a problem with the HDD. Try holding down the power button until you hear it beep a few times, then let go.

Read full answer

Jan 22, 2011 • Sony Playstation 3 (PS3) Console

2helpful

3answers

Iphone 3GS- only get the apple loading screen.

If iPhone won't turn on, or the display freezes or doesn't respond

Press and hold the Home button for at least six seconds, until the application you were using quits.
If that doesn't work, turn iPhone off and turn it on again. Press and hold the Sleep/Wake button on top of iPhone for a few seconds until a red slider appears, and then slide the slider. Then press and hold the Sleep/Wake button until the Apple logo appears.
If that doesn't work, reset iPhone. Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears

More resets:
Try This:
1. Remove Sim Card
2. Hold in 'Home' button and 'On/Off' button together until Apple logo appears
3. Replace Sim Card
4. Hold in 'Home' button and 'On/Off' button together until normal phone screen appears.

Also, Try this:
1.) Shut down the iPhone 3G.
2.) Start up iTunes
3.) Hold down HOME button on the iPhone 3G
4.) While keeping the HOME button depressed, plug in the Sync cable
5.) A message will pop up to ask if you want to reset.
6.) Just click YES and the reset process should start.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Read full answer

Nov 29, 2009 • Apple iPhone 3G

1helpful

1answer

When i turn on ps3 all i get is a blank tv screen? hooked up thru hdmi. triied another hdmi cable i know works still a blank tv screen

when you turn your ps3 on ..try holding the power button down for about 10 seconds..that shud cure your delema..if the ps3 is working properly

Read full answer

Nov 06, 2009 • Sony Playstation 3 (PS3) Console

0helpful

1answer

I only see blank screen when I turn on the PS3, all cords attached and console working properly, no sound or image. Controller still works to turn off console by holding down PS button and pressing 'X'...

Turn your ps3 off, then turn it back on but continue to hold the power button. It should reset your display.

Read full answer

Aug 02, 2009 • Sony Video Game Consoles & Games

0helpful

1answer

Running OFW 5.51 and have Start & Home button problems.

GIVE ME FREE PSP

Read full answer

Jun 29, 2009 • Sony PlayStation Portable (PSP) Console

2helpful

3answers

Iphone not loading after reset, only apple sign is being desplayed

Step 1. Turn off your iPhone.
Step 2. Hold down the power and home button.
Step 3. When you see the Apple logo, release the power button but continue holding the home button down.
Step 4. Open iTunes and wait for it to tell you that its in restore mode.u try this

Read full answer

Apr 17, 2009 • Apple iPhone 3G

0helpful

1answer

Blank screen

switch the console back on and then hold down the button on the front for about five seconds it will reset the console to its default setings

Read full answer

Feb 04, 2009 • Sony Playstation 3 (PS3) Console

Not finding what you are looking for?

View Most Popular

NordicTrack C2150 Treadmill

Exercise & Fitness

Siri keeps asking "Which setting' What setting should I say?

Apple iPhone Cell Phones

192 views

Ask a Question

Usually answered in minutes!

Best Treadmill

View all Fixya Reports

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Have a manual for Nordic Track NordicTrack C2150 Treadmill? Or just drag it here!

Related Topics:

Console not working properly