Olivia 42'' flat screen and cant get any cabel channels

Hello
First of all reset the TV. for that

press and hold the POWER button
on the TV control panel for 5 or more seconds to reset the TV.
Then connect the TV tt any source like outdoor areiel or cable box etc, select the appropriate input, and retune the TV. First of all, connect it to an external antenna, and set it to autotune.

• You must configure the ANT/CABLE input source before

programming channels (-left-hand column).

• If the ANT/CABLE input signal type is set to Cable, the

automatic channel programming process erases channels

that were previously programmed into the TV's memory.

• If the ANT/CABLE input signal type is set to Antenna, the

automatic channel programming process adds newly found

channels to the existing set of programmed channels (and

does NOT erase channels that were previously

programmed into the TV's memory.) To remove an Antenna

source channel from the memory, you must manually delete

it.

• To tune the TV to a channel not programmed in the channel

memory, you must use the Channel Number buttons on the

remote control.

• Programming channels when the ANT/CABLE input is

configured for Cable will take substantially longer than when

the antenna input is configured for Antenna. This is normal;

however, once channel programming is finished, you should

not have to repeat the programming process again unless
your Cable TV service lineup changes significantly.
Find out the received channels are clear or not. If they are clear, your TV is perfect, and the input device you connects ot the TV is faulty. OK.

If you are on a sat system then you only need one channel programmed, if you are using the cable input, if you just want the channels scanned for a local antenna, then you need to go to the menu and go to programming and change the cable/ant to ant and program.

Which specific model from Toshiba do you have? There are several 42" TVs released with the Regza name. Most of the manuals can be found on the Toshiba support web site. http://www.tacp.toshiba.com/customersupport/

The one that I have allows for the channels to be set from the On-Screen Menu. In the TV mode, press Menu (there is a Menu button on the side of the TV). Navigate with the arrow keys (CH+, CH-, Vol+, Vol-) to the Setup menu and highlight Installation and press Enter (the Menu button is also the Enter key when using the buttons on the TV). Then highlight Channel Program and then Start and press Enter. When the search is done, press Ch+ or Ch- to view a station. To add or delete channels, use the Channel Add/Delete that is one line below Channel Program. Use the enter key to change the check mark status next to a channel. If adding a digital sub-channel not previously found, enter the number manually on the remote using the 100 key to add the dash. If the channel isn't found, an error message will result.

I hope this helps.

Cindy Wells

hi, i have a broksonic model ccv-4500 , these is a monitor or tv because i cant founder the digital cable imput. thanks.

Your SAP/MTS function is most likely turned on. This feature has 3 modes: Stereo, Mono and SAP. Stereo and Mono are easy to understand, it's the SAP that can get you. SAP stands for Second Audio Production. It is used to provide weather, information or an additional language translation of a program. Some broadcasters simply transmit the mono audio over the SAP audio channel when the are not using it for other purposes. Other broadcasters simply do not use it, which does not give you any audio. Look on your remote for a SAP or MTS button. If you do not see one, look in your TV user menu for this feature. If you are using a cable box, look in the audio menu of the cable box. You are looking for something set to SAP... just change it to STEREO. I hope this was helpful.

Try www.remotecodelist.com they may be able to help.

hardrocko

i was watching tv last night on my lg,and it went off and said no signal?so i went to retune and now it says not programmed i cant get my dtv channels back

it means that only one channel save from your tv. press automatic search to search more channel from cable signal. now you can change channel.

Both the TV and the Cable box have Aspect(height/width) settings. You must confirme the setting on the cable box and then do the TV.

1. Set TV to Native, this should show image exactly as the cable box sends it.
2. change Aspect settings on the cable box until you get one that works
3. if you get a good one, then your OK. You will just need to find a setting between the 2 devices that work for you. Also, these settings may change automatically for the TV or cable box based on the channel

plse help, i have a cable ready tv hooked up to the coax out of the wall directly to tv and only get 1-13 channels??????