Machine wont fill bobbin

Question edited for clarity. It is a 'bobbin', not a 'bobbing'.
Is it E6, E7, E4, or is it E674? But the main problem, NO Make and Model. Just Google the Error code like this with make and model before it Margaret.

https://www.google.com/search?q=E674

...

Sounds like it may be a bad solenoid or clutch inside. When it tries to reverse direction to rewind is sounds like it's getting stuck. The lights comming on might be an indication that the machine detects a problem. You could try to open it and see if any of the gears are broken or out of place or if any of the teeth on the gears are missing. But I would get it serviced if you're not comfortable with opening it up.

Electronic sewing machines have a sensor that knows when you are winding. Just place the bobbin on the spindle and push it over until it locks for bobbin rewind. Place thread through one of the holes and allow the bobbin to turn. Now step on the gas and let it fill up.



Take your bobbin carrier out. Place bobbin in carrier so the thread is unwinding, counter clockwise usually. Place the thread under the little slit and pull it until it feels like it is under a pressure. To check for this pressure (tension) hold the thread carrier with thread under tension and gently bob. It should allow a small amount of thread to extend. If not then loosen the screw. If too much extends then tighten. Now, place the carrier and bobbin in the sewing machine and make sure the snap is heard when you place it in there. It has to be seated. I believe this is a electronic machine and you won\'t have anymore problems because it will do the rest of your needed things before you sew. HOPE IT HELPS

Some how the bobbin got wound too tight. The thread must have been caught along it's path or something. You will have to unwind the thread off the stuck bobbin. Once enough thread is off the bobbin it should pull off. After that, throw that bobbin in the trash, it is now deformed and most likely will not work anymore. If you wind your bobbins with the machine threaded always make sure you have your presser foot up and Always use a metal foot.

it's possible that there is a part inside the machine that could be broken, it would be a good idea to have the machine checked.

SE270D. Lift the bobbin and reposition, making sure it is down against the pin.

If this is not the problem, a Sidewinder Bobbin Winder (auxiliary bobbin winder sold with most sewing notions) is a lot cheaper than taking the machine in for service.

I'm assuming you are talking about the rewinding mechanism on top. There are grooves in the bobbin which fit on to the rewinding spindle that holds the two together while the bobbin fills. It may be they have gotten out of synch or the bobbin is a non-standard Husqvarna Viking bobbin for that machine. These usually use green bobbins but they have come out with new colors but all have the Husqvarna logo on the bobbin -- an H. I would try to wiggle it slightly to try to remove it. If still will not come off, try popping it off with a flat head screw driver but be sure to put a folded towel under the screwdriver so that you don't damage the molding of the machine. If you still are unable to get it off, recommend taking it to an authorized Husqvarna Viking dealer. A list of dealers near you is available at the Husqvarna Viking website - http://www.husqvarnaviking.com/us

Good luck.

For $30 you can buy a standalone bobbin winder (Sidewinder) at JoAnn's Fabrics or Amazon. It's a great little accessory (battery or electrical) because it saves wear and tear on your machine but also allows you to wind multiple bobbins without having to unthread the machine.

I have had this problem, easily fixed by twisting the rubber knob that is in contact with the spool to the left.

Just click below for the guide how to put the needle ;

Sewing Machine 101- Sewing For Dudes (and Ladies) No. 2: Stitches ...
Anatomy of a Sewing Machine. 1) Bobbin winder 2) Spool pin 3) Thread guide 4) Tension Knob 5) Foot and needle 6) Bobbin housing regards,

Hope it may helps you;

Regards,
VOTIT