Lamp light is on - Mitsubishi WD-73735 Television

Interior lights and the power door locks are controlled by a electronic control module . Hooking up a factory or some other type professional scan tool an checking for codes an viewing input data to these control modules would be the first thing to do.
The interior lighting system consists of the following:

• lighting control module (LCM)
• driver door module (DDM)
• instrument panel
• dome/map combination
• courtesy/reading lamps
• orientation light
• door lamps
• footwell lamps
• luggage compartment lamp
• glove compartment lamp
• vanity mirrors
• door ajar switches
• viewing wiring diagrams an checking power and ground circuits for these modules would be the next step if no codes were found . Principles of Operation
  Lighting Control Module This vehicle uses a lighting control module (LCM). The LCM is a microprocessor-based module that controls several vehicle subsystems, responds to electrical input signals from various switches, sensors, and external modules and is located on the LH side of the instrument panel. LCM subsystem functions include:
  
  • headlamps with autolamps
  • turn signal lamps/hazard flasher lamps
  • cornering lamps
  • parking lamps
  • daytime running lamps
  • interior lamps
  • demand lamps
  • battery saver
  The LCM interfaces with the driver door module (DDM) via the standard corporate protocol (SCP) network for the illuminated entry feature.
  The interior lamp is illuminated by pressing the individual interior lamp switch. The interior lamp is also illuminated by door ajar switches located in the door latches, when any door is opened. A theater lighting feature gradually increases or decreases the light intensity when switched by opening or closing a door.
  The dome/map lamp combination are located on each side of the interior lamp. The map lamps are operated independently of the interior lamp by two switches located on the interior lamps.
  The interior lamps are illuminated by holding the panel dim switch in the UP position until the dome lamps turn on. The interior lamp also illuminates when a door is opened and actuates the door ajar warning lamp switch in the door latch.
  The front map lamps are powered by the demand lighting circuit and the interior lighting circuit.
  The rear passenger reading lamps are incorporated into the rear seat assist handle and are located over the rear door openings. These lamps are illuminated through power supplied by the LCM demand lighting circuit.
  Interior lamps (controlled by the LCM) are activated by using the dome lamp switch (instant ON/OFF response) or when a door is ajar. The following lamps illuminate for interior lighting:
  
  • instrument panel interior lamps
  • front map lamps
  • rear reading lamps
  • door lamps
  Demand lighting includes lamps that are illuminated by the customer by directly actuating a switch. The front dome/map lamps are located in the overhead console. Each lamp is controlled by its own switch.
  The following demand lamps are powered by the demand lighting output of the LCM:
  
  • glove compartment lamp
  • vanity mirror lamp
  • luggage compartment lamp
  Each lamp has a dedicated switch that closes to ground to illuminate the lamp.
  The front map lamps are powered by either the demand lighting circuit or the interior lighting circuit, depending upon the position of the switch associated with each lamp. When the customer turns the front map lamp switch ON, the front map lamp is illuminated through power supplied by the LCM demand lighting circuit. If the customer moves the map lamp switch to the OFF position, the power from the LCM demand lighting circuit is interrupted and the lamp is reconnected to the interior lighting circuit.
  The rear reading lamps are powered by either the interior lighting circuit or the demand lighting circuit.
  The luggage compartment lamp is controlled by the trunk ajar switch, and is powered by the demand lighting output from the LCM, and is mounted near the center of the upper rear panel.
  The glove compartment lamp system consists of a glove compartment lamp switch and wire and miniature bulb assembly. Opening the glove compartment door closes the switch which provides power to the glove compartment lamp switch and wire. The glove compartment lamp switch is grounded to the body sheet metal.
  The vanity mirror lamp system consists of a switch and bulb assembly in the RH inside visor and the LH inside visor. Lifting the vanity mirror cover closes the vanity mirror lamp switch and provides power to the lamps.
  The illuminated entry system is controlled by the LCM and provides interior lighting upon entry to the vehicle.
  Interior lamps will be illuminated for 25 (±1) seconds which includes a theater lighting ramp-up time (0.5 seconds). This time interval does not include the theater lighting ramp-down time. Interior lamps will be turned off before the 25 (±1)-second timeout if the ignition switch is turned to the RUN or ACC position.
  The illuminated entry system has the following additions to accommodate the remote entry system: pressing the unlock button on the remote transmitter will activate the illuminated entry system (with theater ramp-up). When the driver door module detects a button press, it sends a signal on the J1850 communication network activating the interior lamps. The lighting control module will turn off the lamps by sensing the all doors lock signal.
  The battery saver feature prevents excessive drain from loads inadvertently left on. When the ignition switch is turned OFF, power is interrupted to the interior lamps and headlamps (after a 10-minute timeout) and the demand lamps (after a 30-minute timeout).
  The battery saver has the following inputs:
  
  • luggage compartment door ajar switch
  • dome lamp switch
  • ignition switch status
  • illuminated entry signal
  • headlamp switch
  • driver/passenger door ajar entry switch
  • keyless entry remote transmitter
  • door unlock, luggage compartment door release

Do your headlamps work ?
Park/Marker/License/Tail Lamps
Voltage is applied to the turn/headlamp switch at all times. When the turn/headlamp switch is in the PARK or the HEAD position, voltage is applied to the following components:
?€¢
The park lamps

?€¢
The marker lamps

?€¢
The tail lamps

?€¢
The license lamp

The front marker lamps are grounded through the turn filament of the respective front park/turn lamp. The front marker lamps light as a result.
The automatic lamp control function turns on the park lamps and the headlamps. This action occurs when the ambient light sensor determines that the exterior lamps should be turned ON based on the amount of available light. When the BCM grounds the park lamp relay, voltage is supplied directly to the park lamps, bypassing the turn/headlamp switch assembly. When this action occurs, the following conditions exist:
?€¢
The automatic lamp control relay is grounded.

?€¢
The headlamps turn ON. Refer to Headlights/Daytime Running Lights (DRL) Circuit Description .

The lamps turn OFF when the BCM does not ground the park lamp relay or the automatic lamp control relay. This action is caused by the following conditions:
?€¢
The available light reaches a predetermined level.

?€¢
The ignition switch is turned to the OFF position

Park lamp fuse 20amp located in the under hood fuse box .DRL control module
Daytime Running Lamps (DRL) Control Module
Right of the steering column, behind the IP
Park, Sidemarker, Tail and License Lamps
Voltage is applied continuously to the PARK fuse to the headlamp and the instrument panel (IP) lamp dimmer switch through CKT 1340.
When the headlamp and the (IP) lamp dimmer switch is in the PARK or HEAD position, voltage is applied to CKT 9 thus activating the following lamps:
• The park lamps
• The side marker lamps
• The tail lamps
• The license lamps
The park/turn lamps are the only lamps that do not activate yet receive a current from CKT 9. The park/turn lamps do not activate because the voltage drop across the front side marker lamps is much higher than that across the turn lamp filaments Step
Action
Normal Result(s)
Abnormal Result(s)*

1
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
The following lamps light:
• The license plate lamps
• The taillight lamps
• The front side marker lamps (Domestic)
• The front parking lamps (Domestic)
The headlamp position lamps (Export)
Refer to Park Lamps Inoperative
Park Lamps Inoperative
Step
Action
Value(s)
Yes
No

1
Inspect the PARK LP fuse.
Is the fuse open?
--
YES - Go to Step 2
NO - Go to Step 3

2
Repair a short to ground in CKT 1340.
Is the repair complete?
--
Go to Exterior Lights System Check
--

3
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal R and ground.
Did the test lamp light?
--
Go to Step 7
Go to Step 4

4
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal O and ground.
Did the test lamp light?
--
Go to Step 5
Go to Step 6

5
Replace the headlamp/IP lamp dimmer switch. Refer to Headlamp Switch Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

6
Repair the following conditions in CKT 1340 between the PARK LP fuse and the headlamp and the IP lamp dimmer switch harness connector terminal O:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check
--

7
Repair the following conditions in CKT 9 between the headlamp and the IP lamp dimmer switch harness connector terminal R and S204:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check

Usually 8 flashes means the lamp is not lighting.
When most lamps go bad , they physically crack because of excess heat.
The problem is probably the lamp or the ballast, which makes the voltage to light the lamp.
Replace lamp and remember to close the lamp access door after replacing, because the lamp will not light if the door is open an

The SJB supplies power to the interior lighting system. The SJB will set DTCs if certain circuit failures exist with the interior lighting system.
Visual Inspection Chart Mechanical Electrical

• Courtesy lamps
• Map lamps
• Luggage compartment lamp
• Vanity lamps
• Glove compartment lamp

• Smart junction box (SJB) fuse 3 (15A)
• Circuitry
• Courtesy lamps
• Map lamps
• Luggage compartment lamp
• Vanity lamps
• Glove compartment lamp
• SJB

Check fuse # 3 SJB

Hi, You old lamps were compromised due to long usages while the news lamps are defective. They may manufacturing defect. Please claim the new lamps to supplier then.
Regards ,Jay

Lamps last between 5,000-8.000 hrs Keep in mind every hour you play TV ,thats an hour lost on Lamp and its also possiable to receive a defective Lamp even new doesnt mean it works.
Lamp Fan if defetive can also prevent lamp from lighting. This happens to protect lamp from running and getting way to hot and therfore buring lamp up .
Ballast Board that connects to lamp is what turns the lamp on,if the ballast board is defective Lamp will not firer,meaning you either have bad lamp fan or new lamp is defective. Heres another Tip Sony had alot of problems with their Light Engines prices for that part range from $650.00 up to $2,799.00 depending on which light Engine you have? Since your TV is Still under warranty take it in quickly and be sure to ASK about warranty on YOUR Light Engine!!!

Change thermostat and service it.Then solve your problem.

Lamp is near end of life. Try reseting lamp timer and order new lamp if unit stays on

red light indicates lamp is expired. even though you get temporary light, the lamp is shot. Try BULBMAN.COM for a new lamp.