Question about Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348

1 Answer

Slow forward I released the transmission in order to push it to point where it could be jumped to start. After starting, I re-engaged transmission with engine running (contrary to later discovered owners manual warning). Now tractor goes very slowing in forward. Purged per manual, no improvement. What do I do? Did I break something?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Husqvarna Master
  • 653 Answers

To freewheel the tractor using the freewheel lever at the rear of the tractor would not damage the tractor. Check your belts and make sure the lever is all the way back in.

Posted on Nov 28, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 81 Answers

SOURCE: HYDRASTATIC TRANSMISSION DOESN'T MOVE

Far as I know the warranties are not transferable. Some hydrastatic transmission fluid can be checked by removing the battery and underneath there is a place to put the fluid and to check it. But not all models or makes gives you this option.

Posted on Jun 22, 2009

  • 127 Answers

SOURCE: Husquavarna tractor battery won"t start engine

YOU NEED TO REPLACE THE SOLENOID IT IS SHORTING OUT AS TO THE GAUGE THEY WILL NEVER MOVE AS THE GENERATOR CHARGES ONLY WHEN THE BATTERY HITS 9 VOLTS THEN IT ACTIVATES TO CHARGE BACK TO 12 VOLTS BUT IN SMALL INCREMENTS

Posted on Jun 26, 2009

  • 95 Answers

SOURCE: engine dies when clutch brake released on husqvarna gth2548

First check the seat switch,make sure it is plugged in tightly, these plugs have a safety tab built into them that will cut the engine off if you unhook it,sometimes the plug latch pulls out slightly and this will cut the engine, There are two other switches in the system one on the foot clutch and on on the mower clutch, if you follow the white wire from you ignition switch it will lead you to both of them,check those connections also.

Posted on Jul 31, 2009

youcandoit2
  • 11 Answers

SOURCE: just purchased Husqvarna YTH2348 Purged

As for whining sound I believe this normal. The purging instruction using the bypass valve ingaged on low engine running. Next with the bypass disengaged followed by the fwd with fast breaking and or rev with fast breaking actions to get the wheels to turning and getting better responce takes time. This does take some time to do - in my case 15 minutes or more. My tractor had 65 hours on it before it showed signs of not pulling a slight hill. I had to remove the transaxle and put in 50 wt. motor oil and with the purging I was able to bring new life back to this tractor. The original 30wt. motor oil is fine for a brake in oil and I did drain it and took the bottom cover pan off and cleaned the metal particals on the magnets and cleaned the filter. These transaxle are sealed but have a vent plug at the top of the case. That little plug is hard to get off with out damaging it. My tractor whins in forward and reverse but has good hydrostatic power now. So I say the whin is good!

Posted on Aug 03, 2009

mickey813
  • 472 Answers

SOURCE: hi i have a husqvarna ride on lawnmower that moves

sounds like your bely or one of the pulleys are wore out ck the pulleys and ck to see if the belt has sliped off the pulley

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not move when peddle is pushed


there is a safety shut off switch when blade is engaged. may be stuck on

Oct 17, 2015 | Garden

1 Answer

Mower dies when directional pedal ( F/R) or engageing blades


check the safety switches start with the one on the pedal

May 16, 2012 | Garden

1 Answer

My 2000 ford explora wont shift into park, i have to leave it in reverse to get the key out and put the Ebrake on and shut it off. when i put the car in drive it goes all the way to the number 1, can you...


The shift linkage is out of adjustment.

The cable bolt may be loose up at the column, the column itself may be loose enough to allow it to shift position as well.

Make sure column is securely mounted, If not- tighten the 4 bolts that hold it to the dash support so it is. if it is, crawl under driver's side and on the transmission is a bracket where the cable assembly comes into it, and from there a rod that attaches on the lever on the side of the transmission. Make sure the bracket is not damaged or cracked first- if it is, replace it. There is a captive clip to release on the wide part of the piece that the bracket holds, it does not come out fully, but it will release the cable housing so you can slide it to adjust it. With the column shift in Park position, note where the rod is at the transmission. Also make note if the bracket is in line with transmission. If bracket is in line, pull the lever rearward one notch/detent that you will feel engage the lever- this moves the transmission lever to neutral, then with firm pressure push lever forward so you feel 2 distinct notches/detents forward, the lever is now in park. Push locking clip back into position once you confirm the cable outer housing is squarely seated into bracket opening and is soundly clipped into the square opening of the bracket.

If the lever will not move to that second detent or you did not feel it, you will need to check by putting the column shift to first gear position, release the connection to the lever on the transmission just to verify location of lever, and verify the lever is indeed in first gear- the lever on the transmission will move no further- then count detents forward from the rear stop. you should end up in park, and you may hear the parking pawl engage the output shaft of transmission. move lever back to the rear to the stop, reattach the connection to the cable, put column in park, release the clip again and verify the lever is as far forward as it is going to move. Push clip into lock position.

Start Explorer, with foot on brake pedal, release the emergency/parking brake and see if the vehicle moves, or if it is truly in park. It should be in park.

If you encounter some dificulty with getting the column shift lever itself moved over to park- apply brake pedal to release the park interlock mechanism.

Jan 30, 2012 | 2000 Ford Explorer

1 Answer

Started craftsman lawn tractor 24 hp kohler engine drove it a few feet engaged blade clutch and mower stopped. disengaged blade clutch tried to restart . engine turns over starts runs few a few seconds and...


You should be able to push it forwards as well as backwards. I had a similar problem (engine stalling) with mine. I found out if I half choke it, it will stay running. Transmission may still have a problem.

Jul 29, 2017 | Craftsman 24 Hp 48" Deck Yard Tractor

1 Answer

I have a Husqvarna 2754GLS lawn tractor. I pulled the pin to disenage the transmission so the tractor could be in free wheel mode. The pin will not go back into place to disenage free model. I push the...


The pin disengages a " Dog Clutch " . In order for it to re-engage , the dogs need to be aligned. To do this , release the pin and rock the tractor forward or back till the drive re-engages. Cheers

Dec 31, 2017 | Garden

1 Answer

JD 855 the idle spring broke and th hydrostatic pedals would not return to their neturel position . before I new what had happene I pushed the reverse and the tractor lunged backward then I pushed the...


Yes there is a safety switch.And this safety switch has to be engaged.If its not engaged then the JD tractor will not start. On JD 855 the safty switch is located under the seat, There is a rod that must be depressed before engage Somehow that rod is bent or its not pressing the switch to the point that the seat would not fully engage the safty switch.In some cases the switch itself is faulty.It has to be checked . Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Jul 20, 2010 | John Deere 420,1020,2010,2020,2510,2520...

2 Answers

The tractor will not go forward or backward it starts right up but will not engage


1) The drive belt between the engine and transmission has broken or jumped off a pulley.
OR
2) Your hydrostatic transmission is dead.

DO NOT STICK YOUR FINGERS UP INSIDE A RUNNING MOWER TO SEE IF THE DRIVE BELT IS MOVING.

Jul 01, 2010 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

1 Answer

Transmission will not engage and slips when it does engage


auto trans operates on fluid pressure. if the trans has never been serviced, more than likely the filter is plugged, and or the fluid is bad. no doubht its burned and will smell and look like it. get it towed to a shop and have the fliud and filter changed first, then check the band adjustment.recommend a trans shop do it and not jiffylube.

Jul 20, 2009 | 1995 Dodge Avenger

Not finding what you are looking for?
Husqvarna Lawn Tractor 48" Deck, 23 Hp, Model# Yth2348 Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

J. Bradshaw

Level 2 Expert

121 Answers

Jay Finke
Jay Finke

Level 3 Expert

1389 Answers

lnbn1975

Level 2 Expert

204 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...