Error 0xd5d010d reset power displayed and leds winking

Hello, your error is about the ink absorber.

"Ink absorber full Japan:
[5B00]
Others:
[5B01]
P07 The ink absorber
becomes full.
Replace the ink absorber (ink absorber kit), and
reset the ink absorber counter."

This is the way to enter service mode:
"Start the printer in the service mode.
i. With the machine power turned off, while pressing the Stop/Reset button, press and hold
the ON button. (DO NOT release the buttons).
ii. When the Power LED lights in green, while holding the ON button, release the Stop/Reset
button. (DO NOT release the ON button.)
iii. While holding the ON button, press the Stop/Reset button 5 times, and then release both
the ON and Stop/Reset buttons. (Each time the Stop/Reset button is pressed, the Alarm
and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm
LED.)
iv. When the Power LED lights in green, the machine is ready for the service mode operation
and "0" is displayed on the 7-segment LCD.
2) Start the Service Tool on the connected computer.
i. When a button is clicked in the Service Tool dialog box, that function is performed. During
operation of the selected function, all the Service Tool buttons are dimmed and inactive.
ii When the operation is completed, "A function was finished." is displayed, and another
function can be selected.
iii If a non-supported function is selected, "Error!" is displayed. Click OK in the error message
dialog box to exit the error."

You can use the service tool to reset this error after you have enter service mode.
here is the service tool:
http://www.4shared.com/file/QptYmQTM/ServiceTool_V1074planet.html?

change plastic strips of your printer.

Some HP machines have 3 reset levels.

I do not know if the 5610 had them but it's worth a try.

Power off printer, then press and hold buttons while powering on, if it doesnn't reset, then unplug it and press and hold buttons while plugging it in, please tell us if the machine even tries to reset.

# and 3 Partial Reset

# and 6 Semi-Full Reset

# and 9 Full Reset

A Full Reset will clear any stored information in the printer, speed dials, etc, so always start with a partial reset and work your way up.

These procedures will clear the error on the led display of your printer

1. Turn off the printer
2. Press and Hold both the Power and Reset button for 10 sec
3. While Holding the Power button..release the reset button
4. Press the Reset button twice then release the Power button
5. Wait until the printer display " 0 " (or RESTART) on the led screen
7. Press Reset button 4x
8. Press Power button 3x and wait for printer to power off
9. Press the Power to turn on the printer

Do this as many times if the first attempt didn't work until it fully reset.

Start the printer in the service mode.
i. With the printer power turned off, while pressing the Stop button, press and hold the ON
button. (DO NOT release the buttons).
ii. When the Power LED lights in green, while holding the ON button, release the Stop button.
(DO NOT release the ON button.)
iii. While holding the ON button, press the Stop button 2 times, and then release both the ON
and Stop buttons. (Each time the Stop button is pressed, the Alarm and Power LEDs light
alternately, Alarm in orange and Power in green, starting with Alarm LED.)
Without the scanner (connect the operation panel unit.);
While holding the ON button, press the Stop button 3 times, and then release both the
ON and Stop buttons. (Each time the Stop button is pressed, the Alarm and Power
LEDs light alternately, Alarm in orange and Power in green.)
iv. When the Power LED lights in green and "Service Mode Idle" is displayed on the LCD, the
printer is ready for the service mode operation.

Start the Service Tool on the connected computer.
i. When a button is clicked in the Service Tool dialog box, that function is performed. During
operation of the selected function, all the Service Tool buttons are dimmed and inactive.
ii When the operation is completed, "A function was finished." is displayed, and another
function can be selected.
iii If a non-supported function is selected, "Error!" is displayed. Click OK in the error message
dialog box to exit the error.

(7) Main Main ink absorber counter
resetting
Set a sheet of A4 or Letter sized plain paper. After
the ink absorber counter is reset, the counter value
is printed automatically.

(8) Platen Platen ink absorber
counter resetting

error 5b00

reset waste absorber counter. here is how to reset.

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the LED lights in green, press the Stop/Reset button 4 times.

If this does not work you need to call canon.

Good Luck

try switch off, unplug, hold up and down & reset button at the back, swith on

Service mode operation procedures *
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding the Stop/ Reset button.
2) When the Power LED is lit, press the StoplReset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop 1 Reset button (regardless of order), the printer will move into a service mode. (Waiting for menu selection)
4) When the LED lights in green, press the StoplReset button the specified number of time(s) according to the function listed in the table below.(Each time the StoplReset button is pressed', the LED lights alternately in orange and green, starting with orange.)
4 times
Green
Waste ink counter reset
See waste ink counter reset
procedures helaw.

This seems to be a hardware issue.
Only step which can be tried is a power flee and reset if it works it is good if not you may have to replace the printer.
First power flee.
Unplug the power cable from the All-In-One when the printer is turned On and also unplug it from the wall outlet or surg prtector leave the power cable unplugged for about 1Mins or more atleast.
Then Connect the power cable directly to wall outlet without the surg prorector first and before connecting the power cable to the All-In-One press and hold the # and No 6 button at the same tme and plug the power cord back to the printer without releasing the keys, it should come up with a message as smifull reset if it shows that message then the unit is good if not you may have to replace the unit.

Good Luck

ERROR CODE E000602-0003 what i do