Kelvinator stove with F1 code coming up

E1, F1 are Error Codes indicating a Control Board Failure, and normally time to buy a new stove.

https://www.google.com/search?q=Kenmore+stove+95004102+E1%2C+F1+error

LOC

How to Clear the Oven Lock Mechanism on a Kenmore Stove

https://homeguides.sfgate.com > ... > Home Improvement
Clear the lock mechanism -- as indicated by the DOOR LOC light -- by pressing and holding in the oven door light switch for 20 to 30 seconds. While the switch ...

f1 usually indicates an electronic control failure.

JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

JENN AIR
Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

Whirlpool Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution 4 Digit Failure Codes (for 2 digit codes see below) F1 - E0 EEPROM communication error 1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-E... codes except F1-E3. F1 - E1 EEPROM checksum error F1 - E2 UL A/D error(s) F1 - E4 Model ID error F1 - E5 Calibration shifted F1 - E6 Latch signal mismatch error F1 - E9 Stack overflow F1 - E3 Wiring harness cavity size does not match previously stored value The "Cavity Size Select" jumpers in the wiring harness indicate a cavity size different from that which the control was previously configured for. Check the jumpers in the harness to make sure they agree with the actual oven size.

Hi n5my ,

F1 =  Electronic oven control failure  
Sol. Replace electronic oven control (also called EOC or clock).

The "F9" error code means the EOC (electronic oven control) has found the lock motor switches to be out of sequence or shorted.

Test switches and if there is nothing wrong then replace the EOC.

both of the error indicates the problem in EOC.

Regards
R.K.

F1 Board failure Replace control board (also called ERC or clock).

Hello welcome to fixya,


Below I pasted the fault codes for the two different years of this range.

To diagnose these difference you will need a hands on tech !
this is not an easy thing to determine

JENN AIR
Range/Stove/Oven Fault Codes
Failure
Code Condition Check/Repair F1 Defective touch pad or membrane Replace touch pad or membrane (this problem is usually the touch pad)

JENN-AIR
'Newer Style' Range/Stove/Oven Fault Codes

Failure
Code Condition Check/Repair F1 Power to element relay energized during time of day display Wiring harness shorted or change power relay board (PRB)

Note: for double ovens, change second oven board

You have a fault in the range electrical system

FRIGIDAIRE
Range/Stove/Oven Fault Codes Version 3 Failure
Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace EOC (Electronic Oven Control)

Here are the codes for Tappan ranges:

TAPPAN
Range/Stove/Oven Fault Codes Failure
Code Condition Check/Repair F0 & F1 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F2 Oven too hot Check Bake function, if OK, replace oven temperature sensor F3 Oven temperature sensor open Check oven temperature sensor, should be ~1100 ohms at room temperature. If too high or low, replace oven temperature sensor F4 Oven temperature sensor shorted Replace oven temperature sensor F5, 6, 7 EOC (Electronic Oven Control) failure Replace Electronic Oven Control F8 Lock switches Check switches and replace if necessary