Changed cable company and cannot access belkin @tv advanced setup

Admin may not be a permissible username as many companies ship theirs set as admin. Try a different user name.

Connect a LAN cable from Belkin to your laptop/computer's LAN port, open a browser on your laptop/computer and enter the Belkin's configuration URL. http://192.168.2.1
The default PW = blank (just press Enter) You can now change the default admin password.
You can now configure the wireless settings to protect your wireless network and Internet from unauthorized access. Now configure the wireless card in your computer/laptop with the router's wireless settings. To secure your wireless network from unauthorized access, please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

Connect a LAN cable from Belkin to yourlaptop/computer's LAN port, open a browser on your laptop/computer and enterthe Belkin's configuration URL. http://192.168.2.1
The default PW = blank (just press Enter)You can now change the default admin password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.To secure your wireless network from unauthorized access,please click on this link and follow my instructions :-http://www.fixya.com/support/r3559128-wireless_router_security

Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. Click on WAn settings and set it as your internet service provider settings.Then click on wireless settings enable wifi turn radio on If you want secure wifi then enable WEP security enter WEP code it is your password to connect wifi.. Let me know if you need further assistance. Thanks for using FixYa.

has the cable company activated your access at the new address,have they confirmed the cable is now active?

Len

For that you need to access your router.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
For belkin router http://192.168.15.1
or
http://192.168.2.1

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Then WAN settings configure your router as pppoe connection then add user name and password then Enable DHCP then save and restart router.
Let me know if you need further assistance.
Thanks for using FixYa.

To access in your router, open a blank Browser page and type :
http://192.168.2.1 normally it's this ip :)
(note that A lot of routers setup pages are accessed through [192.168.1.1]).

username : Admin and at password leave it blank otherwise Type : admin

Sure the reset button will fix this, because it will reset the router tofactory defaults and erase all personal settings.

The better and easier way is to connect one of your clients/computers to the router via an Ethernet cable, login to your router (The default is http://192.168.2.1), go back to your wireless settings and either write down the key or delete it.

Now connect from another computer and provide the network key when asked for it. Make sure that broadcasting the SSID is enabled in your router, so computers can "see" the network. (Look at page 47 of your manual for details.)

If you don't have a manual, you can download it here.

If you have any more questions or need assistance with any of these steps, just come back here and leave a comment - I'm happy to help.

Based on the specs that I have read I am going to say you cannot hook up cable to the converter. Best thing to do would be to call cable company that provides service there and see if it was turned off on the billing side they probably just didn't come out and disconnect from the pole. That might give you service but missing some features such as tv guide channel. Now some tv's have tv guide built into them and maybe in the move that feature on the tv was turned off it they were using it that way before. Here is what the specs say about that converter:

Use this digital-to-analog converter to convert digital TV broadcast signals to analog signals on analog TVs with antenna-based reception.

I’m happy to help further over the phone at https://www.6ya.com/expert/brandon_60dfebff379d64bd

You need to access the setup page of your Belking router and go to the wireless setup, look fro Use as Access Point, now just a reminder this will defeat the NAT IP sharing feature of the router. Configure the IP address of the router to the same subnet as the network your tying to bridge here's the more detailed procedure:

1. Enable the AP mode by selecting "Enable" in the Use Access Point only page. When you select this option you can now change the IP Settings.

2. Set your IP settings to match your network. Click "Apply Changes"

3. Connect a cable from the LAN port of the router to your existing network.