Teamlava customer support

SOURCE: Microwave stopped heating!

.
This may have already been dealt with, but others can benefit from an accurate, thoughtful reply to this problem.

Concerning the problem Guest is having with the fan coming on when the door is open.

This is usually caused by either a bad door switch, a loose door switch mount, or a problem on the control panel.

Even though a door switch clicks, it may still be bad inside.

If you or a friend decide to look into it, we have critical information on safety, disassembly and door switches at our site, linked here on Fixya: http://tinyurl.com/yzjozk

Concerning the original problem of no heating:

Generally, the most common causes of a failure to heat are:

- bad door switches or door switch mounts
- loose connection at the magnetron
- problem or loose conneciton on the control unit circuit board
- bad magnetron or other high voltage part

If you or a friend decide to look into it, we have critical safety information, info on door switch diagnosis and replacement, and
disassembly information at our site, linked here on Fixya: http://tinyurl.com/yzjozk

SOURCE: Scroll lock on Logitech LX 710

1. Click on Start and click on "Run"
2. Type osk and click OK.
3. You will see the On Screen Keyboard (OSK)
4. If the "nlk" button is white, it will be a visible key on your keyboard. Blue is when the key is not visible and the dark blue with the red border when the NumLock is ON.
5. Please make sure the "nlk" button is blue.
6. You will also the display on your monitor when the slk button is clicked or changed on the OSK.

SOURCE: Radio turns off by itself

I have a 1994 Jeep Grand Cherokee and radio turns itself off without intervention!!

SOURCE: my lg phone keeps turning itself off

1.try making sure the battery always makes contact all the time(if not contact - add some paper for example)
2.the battery should have over 2 lines... (i guess you have charged it many many times)
3.try to update your firmware (software version) from www.lg.com - it should take about 30-60 mins
4. if nothing works, go to a professional service or something like this

SOURCE: My washer is flashing E:13; locked with wet clothes inside

Hello and welcome to fixya.

The E13 error code on the WFMC series Bosch washer`s refer to a drainage problem, as you may or may not already know. ( or in Bosch terms "pump time exceeded" )

What you may have is either a clogged pump, improper detergent being used, ( must use "HE"/lo-sudsing detergent ) hence suds not allowing a proper drain cycle, or wires loose at the pump...the later being the least likely.

You haven`t mentioned if you`ve checked the pump...just hoses as you did mention.

Anyway, here`s the most likely way to remedy a E13 code.

**Unplug the washer from the wall or turn off the breaker before attempting any repairs**

1. Get some towels and if possible a wet/dry vac. If the machine drained, it won't be too bad. If your machine is stuck full of water, I can't say, hopefully you won't get wet. ( maybe you`re lucky enough to be close to a floor drain )
2. Locate the round door on the front of the machine (about 6" in diameter, lower right corner)
3. Find a drill bit or small screwdriver that fits in the hole in the round door.
4. Insert the bit into the hole in the door. It will push in a tab, it doesn't take much force. Rotate the hole (clockwise) to 6'oclock and it should come free. (the edges are very sharp so be careful or wear chain-mail gloves).
5. Once the door is out of the way you'll be greeted by a 3-4" plastic cap with wings so you can unscrew it by hand. ( you should also see a red ring with a string attached, if you pull this the door should unlatch, but getting the water out first is usually a good plan ) There is a small collector lip at the bottom of the cap, that is where you can hold the wet/dry vac to catch the water. Unscrew slowly so you don't get flooded, until it is unscrewed all the way out.
6. Now pull out the trap and visually inspect the inside of the pump as well as the filter/trap. Hopefully you'll find the item/debris that initiated the error code.
7. After removing any debris or obstruction`s re-install the button trap/lint filter and plug the washer in to power or reset the breaker and give it a test.
8. Run a load and watch for leaks. Leave the pump access door off until you are sure you screwed the cap in tight and there are no leaks.

Ultimately you may have a faulty drain pump, but I would certainly start by performing the things I listed first.

Let me know if you require further assistance and if not and this solves your problem, please rate the solution I provided accordingly.

Thank you for coming to "fixya" and good luck.

macmarkus :)

Testimonial: "Thank you! Ten p.m. on a Sat. night...no help in sight...you helped us fix the problem on our own. Thank you so much!"