How set factory default xerox 7800 - Xerox Printer Division Xerox Phaser 7800/GX Tabloid-size Color Printer

REPLACE THE SD CARD

Most likely cause is corrupted software which requires an alt boot which requires the Xerox laptop to reinstall.

The default userID is 11111, and the default password is x-admin http://www.office.xerox.com/userdoc/CC_WCM_WCP_123_128/CC_WCM_WCP_123_128_Web/pdfs/Quick_Networka_Setup_En.pdf
this guide should let you set dhcp and otherwise control it
I was unable to find a "factory reset" solution

Try this link:


http://forum.support.xerox.com/t5/Hardware/Phaser-7800-failure-code-that-I-cannot-find-on-support/td-p/21327

http://www.support.xerox.com/support/phaser-3300mfp/support/enus.html

Solution : Clear Memory and Restore Default Settings on the Machine NOTE:Clearing memory on the machine will remove information from the machine and restore factory default settings. Make sure that all fax jobs have been completed before clearing the memory, or jobs will be lost.
To clear the machine memory and restore factory default settings:

1. Press the [Menu] button (located below the Display Screen on the Control Panel) until "System Setup" is displayed on the bottom line of the Display Screen.
2. Press the [Enter] button.
3. Press the left or right [Scroll] (arrow) button until "Clear Setting" is displayed.
4. Press the [Enter] button.
5. Press the left or right [Scroll] button until the option to be cleared is displayed. (Refer to the table below for additional information.)
6. Press the [Enter] button. "Yes" will be displayed.
7. Press the [Enter] button again to confirm.
8. Repeat steps 3 through 7 to clear additional items.
9. Press the [Stop / Clear] button to return to Standby mode.

Clear Memory Descriptions Options Description All Settings Clears all of the data stored in memory and resets all of the machine settings to the factory default settings. Fax Setup Restores all of the Fax options to the factory default settings. Copy Setup Restores all of the Copy options to the factory default settings. Scan Setup Restores all of the Scan options to the factory default settings. System Setup Restores all of the System options to the factory default settings. Network Restores all of the Network options to the factory default settings. Address Book Clears all of the fax number and e-mail address entries stored in memory. Sent Report Clears all records of sent faxes and e-mails. Fax Rcv Report Clears all records of received faxes. New Scan Report Clears the information about network scan sessions in memory.

JM Liabo
English only on Fixya please. We are a North American website and only converse in English.

hello, I have a phaser 7800? the ignition it puts this code, I switched off and on again? the first switch after 5 seconds as indicated. Same thing, nothing, so I wiped the color sensors. The problem persists. What to do?

Call for Xerox Service

https://translate.google.ca/?sl=auto&tl=en&op=translate

Fixes

Xerox Phaser 7800 - Error Code - PrintCopy .info

https://printcopy.info > model=Phaser+7800
Code: 389.601 · Description: RC Sample Block Fail-A1-In. During the A1 (fine adjustment pattern) and C patch detection, the patch at the MOB Sensor In side did .

and more here
https://www.google.com/search?q=Xerox+Phaser+Error+389.601.00

..

check your consumables if it's a grinding noise

Go to the menu, look in setting and scroll through until you see factory default setting. The functionality you're looking for should be in this area.

this should restore it to default.


By default there is no username or password required to access CentreWare Internet Services. If a username and password have been configured for CentreWare Internet Services and you do not remember the username and / or password, reset the printer to factory defaults (NVRAM reset).
To reset the NVRAM, go to the front panel's Main Menu:

1. Select Troubleshooting, then press the OK button.
2. Select Service Tools, then press the OK button.
3. Select Reset NVRAM, press the OK button.
4. Select Reset NVRAM and Reset Printer NOW, then press the OK button to reset all the settings to their factory default values.

In menus you browse to the service tab, then serivice diagnostics. Go to NVRAM reset and perform the NVM reset.
Before you do that, print out a configuration page if you want to rememebr the network settings. It will set the IP address back to default also.