Question about Washing Machines

1 Answer

Bosch Maxx wfl 1300 washing machine - drum making loud squeaking noise.

Everything works fine - but after a spin, a sound like rubber against the drum emitted. No garments visible in seal. Sound emitts with drum empty or full. Turning drum by hand makes same hottirble noise - near to front of drum. Any suggestions much appreciated.Chris.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 31 Answers

Sounds like bearing have failed or the stainless steel drum has detached from its carrier open the door and try to move the drum up and down there should be no movement at all if there is machine will need to stripped down

Posted on Mar 04, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
abhishek33
  • 1239 Answers

SOURCE: Crunching sound at the commencement of spin cycle

hi
The drive belt (or belts) of a washing machine may become worn or damaged, causing noisy operation or stopping the washer entirely. A damaged drive belt is easy to replace. Remove the back panel of the washer to gain access to the belt. To remove the belt:

Step 1: Loosen the bolt on the motor bracket and move the motor to put slack in the belt.

Step 2: Remove the old belt and stretch a new one into place on the pulleys.

Step 3: To put tension on the new belt, use a hammer handle or a short pry bar to push the motor into position while you tighten the bolt in the adjustable bracket. The belt should have about 1/2 inch deflection when you press on it at the center point, midway between the pulleys. If the belt is too loose, it will slip on the pulleys, causing the machine to malfunction. If the belt is too tight, it will wear very quickly and will probably become so hot that it will start to smoke or smell.

Loose pulleys can also cause problems. Most pulleys are fastened to shafts with setscrews around the hub of the pulley. These screws must be tight or else the pulley or belt will slip. The resulting malfunction may seem to be caused by a faulty motor, but it can be corrected by tightening the pulleys and adjusting the belt. For this reason, always check the belts and pulleys before working on the motor.

Posted on Nov 28, 2008

  • 139 Answers

SOURCE: Bosch Maxx WFL 2260

Hey check to see if you can move the drum by hand,, if you cant the the bearings on the drum have gone and it is seized ..

If you can turn it by hand then most likely it is the carbon brushes on the motor..

hope this helps
any questions dont hesitate to contact me im here to help....

Posted on Jan 17, 2008

  • 40 Answers

SOURCE: Loud noise during spin cycle

is it more like a roar or a train going by? if so your rear tub bearing is going out. very expensive have to replace the tub, basket, spinner ring and shaft and seals about 4 hrs for an exprienced tech to do took me 7 hrs to do for the first time. but it will be very close to $1000 to have done not much less to do it yourself.

Posted on Mar 10, 2009

  • 1527 Answers

SOURCE: bosch maxx wfl 1300 washing machine that wont start.

hello could be brushes on the motor. there are 2 black clips that sit on the motor after time these whare down just slide them out and slide new ones in good luck

shaun

Posted on Jul 21, 2009

tony2155
  • 64 Answers

SOURCE: washing machine i not draining out. bosch maxx

two possible reasons that you dont drain pump is blocked or to much soap,

Posted on Mar 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Bosch Maxx WFL 2260 making intermittent noises. Our machine works well but of late it has taken to making a graunching noise (similar to what you get in a car when you don't use the clutch properly). It...


you have a coin or a hairclim or metal part of a zip that is stuck in the filter where the wings of the water pump rotates against it.

Open the filter and try to remove it. Unplug the power first.

Good luck

Bye

Jan 24, 2015 | Bosch Washing Machines

1 Answer

Bosch maxx wfl 1300 washing machine that wont start.


hello could be brushes on the motor. there are 2 black clips that sit on the motor after time these whare down just slide them out and slide new ones in good luck

shaun

Jul 21, 2009 | Bosch Washing Machines

1 Answer

Banging noise on spin cycle


most front loaders are balanced by a large: ready for this: cement block inside at the top of your machine and because spin is so fast it can sometimes hit inside your machine or it has brokin a peice off ,sorry but yours going to have to get the repair person out.adrian

Feb 15, 2009 | Bosch Classixx WFL 2066 Front Load Washer

2 Answers

Bosch Maxx WFL 2260 not draining - nothing in filter - help?!


sounds like a simularproblem i had, a 5cent piece got caught in the drain solenoid (just between the drum and solenoid) , i had to lift up the front and spin the drain pump fan, on empty, then disassemble and clean pump assy and remove 5cent piece, hope this helps.

Jan 25, 2009 | Washing Machines

1 Answer

Drum makes loud whinning noise when spinning at high rpms.


Remove drive belt.and turn drum by hand, if it feels rough or sounds noisy, then the main drum bearings have failed., also check that the main drum pulley is not loose. If you think it is the bearings, then it is quite an expensive repair.
Plz rate this solution.Thanks.

Dec 25, 2008 | Bosch Axxis WFL 2060 Front Load Washer

2 Answers

Bosch Maxx WFL 2061 motor starts running and then stops


Hi ! I have problem with my Bosch Washer wfl 2061 .. It was running till stoped to
realease drain water out... But no drain water come out.. I have checked drain water host... Nothing thaere.. Water was still in the drum Tank... Whoever knows this problem , please kindly suggest or help me to do something.. Thanks.. Peace pkurdnirund@hotmail.com , peacepattaya@gmail.com

Nov 28, 2008 | Bosch Axxis WFL 2060 Front Load Washer

2 Answers

Bosch Maxx WFL 2260


My drum stop, then I put in new carbon brushes. It works very good in 2mouth, now it stop again. Wht can be problem?

Jan 17, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Brad Brown

Level 3 Expert

18087 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...