Error sign shows On Error shows: SG;0015,0404,044 after press restart shows: SG;0015.0036.048

Question 1

0helpful

1answer

Error sign shows On Error shows: SG;0015,0404,044after press restart shows: SG;0015.0036.048

If you are using a windows driver do not use Topix in the graphics.
Use 8 bits or 4 bits. The firmaware may not be able to understand the Topix algorithm. What you have is a syntax error displayed.

Feb 13, 2014 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

Error sign shows

this is syntax error .
Check firmware version
- Topix grahics with firmware version 3 or higher
- Use compress or ascii graphics in the driiver
hope this helps

Aug 24, 2012 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

Tec b-472 gap sensor

use detection transmissve in the driver

Aug 13, 2012 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

TEC B 572 WHEN USING DATA TRANSFER SWITCH BOX.. ERROR CODE SG;0040,1120,1384,00 APPEARS ON 1 MACHINE.

This may be a firmware problem! or problem on the communication port
This is a syntax error detected by the machine

Aug 01, 2011 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

I have a tec b472 printer that is showing and error message that reads - XR;0297,0000,029 Can you tell me what it means

This is a syntax error.
The XR; xxx is to clear a portion of the print image
There is an error in geration this instruction
Reason may be the square drawn is off the label size.
Check the values
{XR;XXXX,YYYY,ZZZZ,AAAA'}
where
XXXX = X start coordinates in 10th of millimeter
YYYY = Y start coordinate
ZZZZ = End X coordinates
AAAA = End Y coordinates

Jan 10, 2011 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

I am not able to print to a local printer TEC 472 on LPT1. I get no error.

The B472 has a contronics SPP mode parallel
Check that you have the correct settings on your computer.
Besides take care the DB25 is a serial connection with
9600,n,8,1 setting by default

Jan 03, 2011 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

Sg: 0284, 0046, 017

Syntax problem
electrical problems or use of topix graphics with a firmware not accepting the commands.
Use 8 bit graphics

May 12, 2010 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

TEC 472 Error message- SG: 139, 0010, 064

This is syntax error, the coorect is SG;0139,0010,064....

May 09, 2009 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

TEC B 472 QQ

Swapping the parallel port to the printer should allow it to connect via parallel. Run through front panel diagnostics before/after install. depending on firmware it will tell you if the parallel board is installed.

Nov 09, 2008 • Toshiba TEC B-472 Thermal Label Printer

0helpful

1answer

TEC 472 QP PRINTER

Try with CUPS --- oh, sorry, it's for Linux only, my bad

Jan 08, 2008 • Toshiba TEC B-472 Thermal Label Printer

Question 2

kong win chang

Toshiba TEC Expert 142 Answers
Posted on Jun 10, 2014

kong win chang

Toshiba TEC Expert

Joined: May 04, 2011

Answers

142

Questions

0

Helped

52884

Points

152

Change graphic settings to 8 bits or 4 bits instead of Topix compression in the driver.
Firmware too old to understand the instructions.

Answer 2 · 5/18/2008 12:00:00 AM

Anonymous

300 Answers
Posted on May 18, 2008

SOURCE: tec 472 qq no print

First of all can you print just from the printer ie
Turn on the power while
holding down the [FEED]
key and [PAUSE] key?

Anonymous

300 Answers
Posted on May 19, 2008

SOURCE: tec 472 qq no print

I can only guess there must be a problem with a setting either within the printer or your pc. It's unlikely to be a hardware fault as the printer self tests ok.
I have repaired quite a few of these printers, but haven't had your problem. I can only suggest your compare the settings (baud rate etc)

A

Anonymous

Posted on Sep 10, 2008

SOURCE: TEC 472 QP PRINTER

Try with CUPS --- oh, sorry, it's for Linux only, my bad

Anonymous

1 Answer
Posted on Mar 26, 2009

SOURCE: TEC B 472 QQ

Swapping the parallel port to the printer should allow it to connect via parallel. Run through front panel diagnostics before/after install. depending on firmware it will tell you if the parallel board is installed.

pkwc

254 Answers
Posted on Sep 04, 2009

SOURCE: TEC 472 Error message- SG: 139, 0010, 064

This is syntax error, the coorect is SG;0139,0010,064....

Answer 3 · 5/18/2008 12:00:00 AM

Anonymous

300 Answers
Posted on May 18, 2008

SOURCE: tec 472 qq no print

First of all can you print just from the printer ie
Turn on the power while
holding down the [FEED]
key and [PAUSE] key?

Answer 4 · 5/19/2008 12:00:00 AM

Anonymous

300 Answers
Posted on May 19, 2008

SOURCE: tec 472 qq no print

I can only guess there must be a problem with a setting either within the printer or your pc. It's unlikely to be a hardware fault as the printer self tests ok.
I have repaired quite a few of these printers, but haven't had your problem. I can only suggest your compare the settings (baud rate etc)

Answer 5 · 9/10/2008 12:00:00 AM

A

Anonymous

Posted on Sep 10, 2008

SOURCE: TEC 472 QP PRINTER

Try with CUPS --- oh, sorry, it's for Linux only, my bad

Answer 6 · 3/26/2009 12:00:00 AM

Anonymous

1 Answer
Posted on Mar 26, 2009

SOURCE: TEC B 472 QQ

Swapping the parallel port to the printer should allow it to connect via parallel. Run through front panel diagnostics before/after install. depending on firmware it will tell you if the parallel board is installed.

Answer 7 · 9/4/2009 12:00:00 AM

pkwc

254 Answers
Posted on Sep 04, 2009

SOURCE: TEC 472 Error message- SG: 139, 0010, 064

This is syntax error, the coorect is SG;0139,0010,064....

Related Topics:

Trustworthy Expert Solutions

Error sign shows On Error shows: SG;0015,0404,044 after press restart shows: SG;0015.0036.048

1 Answer

kong win chang

5 Related Answers

Anonymous

Anonymous

Anonymous

Anonymous

pkwc

Add Your Answer

Attachments: Added items

Related Questions: