Question about Powerwinch 36' Class Freefall P77736 775 Lb Pull

1 Answer

Powerwinch windlass not working.

I just bought the boat and hadn't tried the windlass. At an anchorage yesterday I tried to freefall the anchor and nothing happened. the voltmeter showed a drop as i used the freefall switch so I assumed there was power to the unit or at least to the switch. It wouldn't lift either. The motor doesn't even try to run. No breakers tripped and I don't see a breaker dedicated to the windlass. I think it is an electrical problem but am unsure. The unit appears to be in very good condition and not too old.I would appreciate any ideas you may have. Thank you,
Vince

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Of course, first check the voltage at the connections to the windlass. Have someone operate the switch while you measure with a volt meter. If no voltage check breakers, or fuses. Heavy current devices like a windlass will often require fuses near where they connect to battery power.


A windlass requires a LOT of current to run. Not just voltage. Trace the wires from the battery connection all the way to the windlass. If possible, loosen any connections (ex; a lug with a nut or bolt) and clean with a wire brush then reconnect. Be sure to disconnect the battery while cleaning. Many times wires will corrode past the insulation. Especially if they were not tinned wire to begin with (tinned wire has a silver shine, regular copper has a copper color and typically turns dark or even black when corroded).

Since a windlass requires a lot of current, often there may be a relay near the windlass that might go bad. Listen to see if this is activating while someone operates the switch.

Posted on May 15, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anchor light wireing for hurrcane deck boat


Check the electrical connections, bulb and switch.

Jun 26, 2013 | Westland Godfrey Pontoons & Deck Boats...

1 Answer

Hello, I have a lewmar Concept 1 windlass that worked fine for May/June, then on vacation in July it started cutting out. If I let it sit for a minute, it would start up again, only to quit again after...


Check the brushes and if they are short just replace them.
This will solve the problem.
There is thermal cut out which will protect the winding if its hot and will stop windlass and after cooling down it can run again.

Oct 28, 2017 | Lewmar Concept 1 Windlass 5/16" Gypsy With...

1 Answer

Brand new Powerwinch rc30. It worked fine, 2 times pulling my 21ft. Gradywhite onto the trailer. The third time failed- slipped clutch. Boat weight is 2900 lbs. without motor and fuel. Should I have...


I would try to get it repaired Under warranty.
And later use it in double line...
The weight of your boat is 1, the force needed to pull your boat on the trailer is another thing...

Nov 29, 2017 | Powerwinch RC30 Trailer Winch

1 Answer

Sprint 600 Vertical Windlass blows fuse


Is this the main fuse???
600watts motor on a 12V system drops 50amps...
You should have an 80 or even 100 amps fuse for the power cables!

Jun 15, 2017 | Boating

1 Answer

For the mot, how far away from the seatbelt anchor point has to b


You patch it with fiberglass,just clean up the rust,patch it and repaint it good to go.

Jun 29, 2009 | 1994 Toyota Celica

1 Answer

I have a Lewmar Sprint 600 Windlass. It was working, however, my battires were low and there wasn't enough power to run the windlass. I think trying multiple times, I trick the breaker. I charged the...


I had the same problem this past weekend. Took the complete unit apart and found salt and all kind of moisture in the motor itself. It sure was not sealed very well from the factory. I am unable to find the motor sold separately, therefore I am taking my unit to an electric motor shop. I am guessing it will cost me about $100-$125 to get the motor reworked. It was extremely easy to take apart.

With the moisture in the motor, there was simply too much resistance for the windlass to turn, If you get your tension wrench and work the windlass back and forth, then hit the button. It should work temporarily.

Good Luck,
Tony

Apr 14, 2009 | Boating

Not finding what you are looking for?
Powerwinch 36' Class Freefall P77736 775 Lb Pull Logo

Related Topics:

537 people viewed this question

Ask a Question

Usually answered in minutes!

Top Powerwinch Boating Experts

ray gallant
ray gallant

Level 3 Expert

62997 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

26819 Answers

Tom Chichester

Level 3 Expert

51893 Answers

Are you a Powerwinch Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...