Hitachi cp-x444 remove keylock - Hitachi CP-X250 Multimedia Projector

Power Supply is $50

https://www.google.com/search?q=hitachi+cp-x3030wn+power+supply

CP-X2530WN/CP-X3030WN CP-WX3030WN

Projector Central https://www.projectorcentral.com > pdf > projecto...
The information in this manual is subject to change without notice. • The illustrations in this manual are for illustrative purposes. They may differ.
118 pages

CP-X2530WN/CP-X3030WN CP-WX3030WN

Hitachi in Europe https://estadoc.hitachi.eu > servlet > FileViewer
The information in this manual is subject to change without notice. • The illustrations in this manual are for illustrative purposes. They may differ.
69 pages

CP-X2530WN/CP-X3030WN/CP-EX250/CP-EX300 ...

Projector Central https://www.projectorcentral.com > pdf > projecto...
EW300. Responsible Party Hitachi America, Ltd. Address. 900 Hitachi way, Chula ... Before connecting the projector to a device, consult the manual of the device ...
20 pages

https://www.google.com/search?q=DIODE+T3D+36

https://www.google.com/search?q=HITACHI+CP-X3030WN

Original Projector Ballast Main Power Supply For Hitachi ...

AliExpress https://www.aliexpress.com > item
Original Projector Ballast Main Power Supply For Hitachi CP-X3030WN. 1/1. 1. US $52.62. Price shown before tax. Free shipping?Free returns. Original Projector ...
US$52.62

Projector Power supply For CP-X2530WN CP-X3030WN ...

AliExpress https://m.aliexpress.com > item
Projector Lamp Ballast And Power Supply For Hitachi CP-X2530WN. US $80. Projector Lamp Ballast And Power Supply For Hitachi CP-X2530WN. EUC 215g N/T05 ...
US$50.00

CP-X2530WN/CP-X3030WN CP-WX3030WN

Projector Central https://www.projectorcentral.com > pdf > projecto...
power supply make the projector turn on. Setting up. ?This product is also designed for IT power systems with a phase-to- phase voltage of 220 to 240 V ...
118 pages

....

AIR FILTER FOR HITACHI PROJECTOR CP X200 CP X300 CP X205 CP X305 CP X308...

Air Filter FOR HITACHI PROJECTOR CP X200 CP X205 CP X300 CP X305 CP X308...

go to this website and download the manual
http://www.projectorcentral.com/pdf/projector_manual_2912.pdf

then look at the construction.
you should be able to undo the screws on the underside and lift the cover over the front lens

Yes to replace the lamp you need to remove the 2 screws. You can touch the lamp but I try not to. After the lamp is in you need to reset the hr timer for the lamp. to do this you need to look in manual on page 34.
If you do not have the manual you can get it here at link below.

http://www.aboutprojectors.com/pdf/hitachi-cp-s235-manual.pdf

Good luck

Specifically i don't know. What i do know is mfg's use the same codes, whether they map them to the same functions across a series of remotes can't say for sure. Experiance tells me it will be just fine...

hold rown reset on panel for about 3 seconds, wait for display, press reset again and select 0.

There is a menu item which has both the lamp hour reset and check air flow, etc. You must go into the menu and reset the air flow item. MAKE SURE YOU CLEAN THE DUST FILTER!! Heat is the number one killer of projectors and Hitachi's run "hot". I clean my projector once a week--Hey, I'm not rich. lol! Also, excessive heat will cause the lcd panels to fail prematurely and cause lots of other components to do the same.--Rick

Hi,

You can find the remote in the link below.

CP-X327 Replacement Remote Control

Hi there

Look at the bottom of the Projector , you'll see a thin grey line with two edges on it. That is the filter. Grip on the sides and gently pull it out.