Kenmore error codes

If you are getting an F-5 error code on your Kenmore hood combination, it typically indicates a problem with the temperature sensor. This error code may occur when you are trying to use the convection feature, as you have described.

To troubleshoot this issue, try the following steps:

Turn off the power to the unit and unplug it from the electrical outlet.

Wait a few minutes, then plug the unit back in and turn on the power.

Try using the convection feature again and see if the error code reappears.

If the error code persists, you may need to replace the temperature sensor. You can consult the user manual for your Kenmore hood combination or contact Kenmore customer service for assistance with this.

If the unit is still under warranty, it's recommended to contact Kenmore customer service for repair or replacement options.

https://homeguides.sfgate.com/cuisinart-bread-maker-error-codes-13409633.html


Error code ERROR 1 presents on Kenmore Elite countertop microwaves with model numbers 56561582011, 16755, 56561584011 or 56561589011. ERROR 1 occurs when the unit has not received enough power to undertake a sensor cooking operation. Sensor cooking is a feature of Kenmore Elite microwaves that adjusts the temperature and cook time of dishes contingent upon information received by sensors in the microwave. In order to perform this function, a microwave must be plugged into a power source for at least five minutes previous to doing so. Thus, ERROR 1 indicates that the unit has not been plugged in for a sufficient length of time.

it's the touchpad, you have to stick a new one, call a technician or buy the touchpad corresponding to your microwave oven model

https://www.applianceblog.com/mainforums/threads/51787-Kenmore-Elite-SE-error-code

F7 Error Code On Microwave Ovens With Inverter Board

An F7 error code could be an inverter board failure. Anything else that prevents microwave energy may also cause an F7 error, and must be checked. The technician should perform the following procedure to test for an F7 error code:

1. Check the magnetron.
2. Check the magnetron TCO (it should be closed).
3. Check the 3 interlock switches.
4. Check the harness wiring.
5. Check the electronic controls.
6. Check the inverter board.

For more free help, feel free to contact me via my site with your detailed symptoms and full model number and FCC ID number as shown on the tag in or on the oven.

. The SE error code means the microwave has had a Key short error. The control panel or smart board will need to be replaced.
-korrinA S

Need a model number.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

HELLO.

An F6 error code typically indicates a controlpanel problem. Disconnect power and wait several minutes before plugging itback in. If the F6 error code comes back within a minute of restoring power,the control switch pulse return line is not connected properly. This willgenerally require professional repair.

Thanks.

Hello, please use the chart to determine which stove you have. You will have to look at the model number. The first 3 numbers will be the series on the chart. In most cases an F1 error would require replacement of the electronic control. This part is commonly refered to as an EOC or ERC. However this type of repair is usually reserved for repair specialists.

KENMORE Range/Stove/Oven Fault Codes – 362 Series (General Electric)
F1 = Stuck Touch Pad Key - Replace Electronic Range Control (ERC).

KENMORE - 911 Series (General Electric/Roper)
F0-F1-FF = Failed transistor in Electronic Range Control (ERC).

KENMORE Range/Stove/Oven Fault Codes- 665 Series (Whirlpool)
F1-E0 EPROM Error - Electronic Range Control (ERC).
F1-E1 EPROM Error - Electronic Range Control (ERC).
F1-E2 U/L ERC Errors - Electronic Range Control (ERC).
F1-E3 Fuel Type Fail

Kill power 30 seconds-Cancel-Start/Enter-5 seconds-Should see “E” for electric-
“9” for gas-If code changes again-replace Electronic Range Control (ERC).

KENMORE - 790 Series Electronic Oven Control (Frigidaire)
F1 = Shorted Touch Pad = Electronic Range Control (EOC) Internal check sum error.
Runaway Temp = Replace Electronic Oven Control (EOC).

Kill power 30 seconds - if error returns - replace Electronic Oven Control (EOC).

Thanks

The letter "d" is indicating the microwave is in a demo/learning feature.
To cancel the "demo" mode press and hold "Kitchen Timer" for 5 seconds. Two tones will sound and the small "d" will disappear from the display.

Please reply back with your model number so we can help you.

A full Sears/Kenmore model number usually has 3 digits, a dot, then 8 more digits, such as ###.########