Code is 2h - General Electric WCVH6800J Front Load Washer

I couldn’t find any error code 2H but I did find an error code H2O. This code means insufficient water pressure. If the display reads 2H, it usually means the start delay function is turned on. The dishwasher will turn on in 2 hours if door is closed. This dishwasher is advanced. To understand all operations you should read the user guide or manual.

The error code 2H is not a standard Samsung error code.
You're going to need a on site technician that can access the machine's built-in diagnostic system to find the fault.
Sorry.
Have you unplug/turn off breaker to it for 10 minutes to see if it will do a hard reset? Do before calling tech.

1. Samsung washing machine 2h error code on the screen ...

   www.fixya.com/support/t6531747-samsung_washing_machine_2h_error
   Oct 23, 2010 - The door lock is the problem... try to push the door harder... or change the door lock! It is usually done in 5 minutes.. .... if it is only 5 months... you ...

It not an error it sound like it on a delay of 2 hours

check out http://www.ehow.com/info_8759839_ge-dishwasher-error-code-2h.html

8.3 Battery Configurations

There are different configurations for different battery types and backup time. Here, the batteries from VISION and

YUASA are selected. The backup times ranges from 1hours to 4hours for 20KVA UPS and from 1hours to 2hours

for 30KVA UPS, because of limitation of CLA power rating.

UPS Backup

time Number of blocks Type of blocks Capacity(10H)

1h 1×24 6FM55SGX 52Ah

10kVA 2h 2×24 6FM45X 2×42Ah

4h 2×25 6FM75X 2×74.5Ah

1h 24 6FM75X 74.5Ah

15kVA 2h 3×24 6FM45X 3×42Ah

4h 3×25 6FM75X 3×74.5Ah

1h 1×25 6FM90X 90Ah

20kVA 2h 3×25 6FM55X 3×52Ah

4h 2×26 6FM150X 2×144h

1h 2×25 6FM75X 2×74.5Ah

30kVA

2h 3×24 6FM100X 3×96Ah

Sheet. 4 the battery configuration with VISION battery

UPS Backup time Number of

blocks Type of blocks Capacity

(10H)

1h 2X24 NPL24-12 2X24AH

10kVA 2h 2×26 NPL38-12 2×35.3AH

4h 2×26 NPL65-12 2×60.5Ah

1h 1×27 NPL65-12 60.5Ah

15kVA 2h 2×24 NPL65-12 2×60.5Ah

4h 3×26 NPL65-12 3×60.5Ah

1h 1×27 NPL100-12 92Ah

20kVA 2h 2×24 NPL100-12 2×92Ah

4h 4×26 NPL65-12 4×60.5h

1h 3X24 NPL65-12 3×60.5Ah
30kVA

possible actuator not being fully engaged
check for vacuum leak or faulty unit

I would check the buttons on the control they may stuck. check the delay button..

The control panel needs to be replaced (indicated by the "2H" error code displayed at the start of the cycle).
BTW - The number 1 displayed at the end of the cycle indicates the cycle has timed out (i.e., it doesn't mean 1 minute remaining). Hence the continued running of the unit. Until you replace the control panel, you'll have to manually cancel the cycle at this point.

the problem is h2 not 2h you need to replace the thermistor or try to clean it by an ordinary cloth