ACER APSIRE BLACK SCREENING

Discribe what happens when push the on/off button and you try to boot, fan spin? LED's blink? HDD/DVD light blink? Sound? Any thing on screen at boot? What blue light?

You need to tear down it into pieces to remove that object. Consult a technician

Most fans have 3 wires usually a white, black, and a blue(or black with white stripe) the white wire is the neutral and goes to the white wire in the ceiling box, the black wire is the fan hot lead and goes to the black hot lead in box and the blue(or other blk/wht) is for the lights and would go to the switched lead in the ceiling box(sometimes another color but not white or green)..if you don't have a switched lead coming out of the ceiling box and just two wires then the white goes to the white in the ceiling and both black and blue go to the black wire in the ceiling box

1) To test the timer, put it on another Load, for example a light.

2) Also you can test your wires.
Take wire nut off Black-black connection and test to bare ground >>> tester should light up.
Next take wire nut off Black-blue connection and test to bare ground >>> tester should NOT light up until push button is activated and countdown begins.

3) Another thing to try is reversing the blue and black wire, just to double check your wiring.

If I understand correctly you are installing two wall switches.
Your switches are switch1 and switch2
Each switch has 2 brass-colored screws
If you have a double switch, see page bottom
And you are installing a fan/light combo with separate wires for fan and light.

Bare ground wires and green wires connect to each other and to green screw. A ground wire runs from fan/light to switch box where it connects to other bare copper wire and these wires will not be discussed.

Lets work from the fan/light down to the switch.

Blue-wire-fan connects to either brass screw on switch1
White-wire-fan connects to white Neutral (we'll talk about this wire as we go)

Black-wire-light connects to either brass screw on switch2
White-wire-light connects to same Neutral as White-wire-fan.

So you need 3 wires running from fan/light to your switch box.
One wire arrives at switch box and connects to brass screw on switch1
One wire arrives at switch box and connects to brass screw on switch2
One wire is the Neutral wire and it arrives at switch box and connects to other white wires inside switch box. Twist these wires together and cover with wire nut.

Now your white Neutral is connected to other white wires in switch box.
Each switch still needs another wire.

The Hot black wire from breaker box connects to brass screw on both switches


Pardon the crude drawing.
The switches would actually be located next to each other, but it was easier to draw like this.
Drawing shows 3 wires coming from fan-light to switch box.
The drawing shows the black and white wire arriving from breaker
The drawing does not show how the white wires are joined with a wire nut

If you have a double switch, with 2 switches stacked vertically.
The screw colors can be different.
Double switch could have brass screws on both sides, in which case your Load (fan-light) wires connect on one side of device, and your Hot from breaker connects to other side. It doesn't matter which side, but loads on one side, hot on other side.
Double switch could also have dark screw(s) on one side and brass screws on other side.
In this case, the black Hot from breaker connects to dark-colored screw(s)
And your Load (fan-light) connect to brass colored screws.

If you need more information, or if something is still confusing, answer back.

Most probably the intergrated Graphic on the mainboard of your Laptop is faulty. Too bad, you have to replace it from ACER or any authorised Vendors.
If the cost is too expensive to repair, get a new Laptop/notebook.

Please Try to replace your RAM.

I would recommend downloading Bart PE and than burning an ISO to a CD. Once you run Bart PE get under Command Prompt and enter chkdsk c: /f /r. This can also be done from an XP disk under the Administration console.

Sincerely,

Ryan Deschaine

Systems Administrator

Boxen Solutions LLC

http://www.boxensolutions.com
Email address: [email protected]
Office number: 262.254.0064
Mobile number: 262.834-5844
Fax: 414.918.8432
AOL: BoxenRyan
Twitter: BoxenRyan
W172 N9175 Shady Lane
Suite 418
Menomonee Falls, WI 53051

Aspire One uses Atom process and its very small. it get hot easly and there is a fan on it also fan is so small. you need to change to fan. take the service.
hope it work

have u tried booting the computer with just the power supply hooked up and your battery out? iv'e had the same exact lab top and the battery went bad and the computer wouldnt do anything at all like your talking about. Even if i had the power supply hooked up and the battery. Remove the battery, and try booting it up.