UNLOCK REGION CODE

Hello Patricia -

Please follow the instructions below for unlocking your Philips HTS3011

1. Switch on the DVD player
2. OPEN the disc tray
3. Key 9 9 9 9 0 using the Philips remote control supplied with the DVD player
4. Press PLAY. The disc tray will close.
5. Switch the player OFF then switch ON again.
6. To test, play a disc from a region which was previously locked.

If it does not work the first time, switch the player off and back on, then try again.

This is a verified unlock method, but I was unable to confirm whether it works for players sold locked to Region 1 (North America). If you have a Region 1 player and the method above does not work, you will not be able to unlock your player.
Please note: Unlocking a DVD player may invalidate the warranty. Unlock sequences may not work with some firmware updates and some DVD players have been damaged through failed attempts to unlock them. Unlocking your DVD player is done at your own risk.

Regards,
BElectric

Hi,

From which region is your did player?

Hi -

Please follow the instructions below for unlocking your Philips HTS 3371

Please note: Unlocking a DVD player may invalidate the warranty. Unlock sequences may not work with some firmware updates and some DVD players have been damaged through failed attempts to unlock them. Unlocking your DVD player is done at your own risk.


1. Switch the DVD player ON
2. OPEN the disc tray
3. Key 9 9 9 9 0 using the Philips remote control supplied with the player
4. Press PLAY. The disc tray will close.
5. Switch the player OFF then switch ON again.
6. To test, play a disc from a region which was previously locked.

If it does not work the first time, switch the player off and back on, then try again.

This is a verified unlock method, but I was unable to confirm whether it works for players sold locked to Region 1 (North America). If you have a Region 1 player and the method above does not work, you will not be able to unlock your player.

Regards,
BElectric

Hi there,

This player is relatively easy to change to region free. Please complete all of the steps below to unlock your DVD player.

Please note: Unlocking any DVD player may invalidate the warranty. Unlock sequences may not work with some firmware updates and some DVD players have been damaged through failed attempts to unlock them. Unlocking your DVD player is done at your own risk.

Unlock sequence for the Philips DVP 3020:

1. Switch on your TV and DVD player;
2. Make sure the TV is set to the correct input for the DVD player;
3. Remove any disc from the DVD player and close the disc tray;
4. Press the "SETUP" button on the DVD player remote control;
5. Use the LEFT/RIGHT arrow keys to highlight "PREFERENCE";
6. Enter 1 3 8 9 3 1 using the numerical keys on the Philips DVD remote control;

A pop-up menu will appear on the TV screen.

7. Use the UP/DOWN arrow key and choose "0" for all regions;

That's it. You should now be able to watch DVDs from all regions on your player. It is also a good idea to switch the player to standby and then switch it back on before trying any discs.

This is a verified unlock sequence for the Philips DVP 3020. If it doesn't work the first time, switch the power off and start again at step 1. If it still doesn't work, it is likely that you have updated your Firmware to a new version and this unlock sequence does not work with your firmware version

If you need further assistance, please reply to me from within this page and let me know which firmware version you have installed in your DVD player.

Regards,
BElectric.

Hi,
Please follow the steps : To change the player region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, * requested region code here (1-8) *, Subtitle, 1

3. Player will reset and requested region code will be set.
- For example to set region code to 3 press: "Enter, 6, >=10, <<, 00F2, Audio, 8, 3, Subtitle, 1"

To set the player to RCE proof region free
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 1, Subtitle, 4

3. Player will reset and set to "region-free" and "RCE-free" mode

To restore players factory region code
1. Be sure players drive is empty (nodISC)
2. Enter following key sequence using remote control:

Enter, 6, >=10, <<, 00F2, Audio, 8, 9, Subtitle, 1

3. Player will reset and set to factory region code
Regards, Jay__uji8

Here you go.....

The only thing you do to unlock DVDR3480 is this:

With NO disc in your DVDR3480-player you press SETUP on the remote and then press this code: 5 0 1 8 ,now you can pick Region-code with the remote from 0-6
( 0=Region free)

Karlos

Search google for region-free/multi-region codes codes as well as your DVD Player Model

e.i.: AWA DVDS203 region free codes
e.i.: AWA DVDS203 unlock region

Replace "DVDS203" with whatever model your DVD Player is.

Do not pay for codes! The unlock method may be simply typing some stuff into your remote or having to download firmware upgrades, burn to CD and play on the DVD Player.

Warning: Unlocking DVD Players MAY void some warranties!!

Hi,
I can provide you with this region free unlocking Code.
i do have a small fee for this service, as i have to pay subscription to a world-wide database service provider. who charge me for using thier site.
if you would like to purchase the code, for a small fee.
please e-mail me for further details.
[email protected]

Many thanks Mike @ compurepair.

How do I unlock the region code for a Sony BDP-S570 blue-ray?

It's currently locked to Region 4

Hi
I have tried to unlock the DVD DP271 player using following methods, But it is not unlocking. If any body knows any other code. Please help me to un lock my DVD DP271 player.

Thanks
Sekahr

1. Power up and press setup
2 Scroll down to LOCK
3 Press '0' (zero) seven times
4. A message may now appear with saying that the player is region free.
5. Power down then power up.

or

1. Remove any discs and power up the DVD
2. Press PAUSE
3. Enter 314159
4. The hidden region code menu may now appear.
5. Set code you want- 0 for multiregion, 1 for region 1 and so on
6. Press PAUSE
7. Power down then power up