Question about KitchenAid Dishwashers

1 Answer

KUDP01ILBL6 The handle was broken, it was still working somehow, but since last week it stop working. The lights were up on the panel. I can select normal wash then that light is on, but cancel light is blinking all the time. I ordered the handle part and replace the broken one, but no change not he front display. the cancel light still blinking....

Posted by on

  • 3 more comments 
  • shyboy67362
    shyboy67362 Feb 04, 2014

    Pressing start is not starting the dishwasher, all the other buttons seems to be working except the start button.

  • shyboy67362
    shyboy67362 Feb 04, 2014

    https://imagizer.imageshack.us/v2/2750x1...

  • shyboy67362
    shyboy67362 Feb 04, 2014

    These are the buttons that I have, does not have sanitize and heat button, so what would be the seq?

  • shyboy67362
    shyboy67362 Feb 04, 2014

    These are the instructions, which I guess means that the switch is bad? but not surehttp://imageshack.us/a/img837/3204/c64n....

  • shyboy67362
    shyboy67362 Feb 04, 2014

    This is the main control board.http://imageshack.us/a/img547/7674/ukc5....

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 111 Answers

Technical sheet say you have a stuck key on the keypad

Posted on Feb 06, 2014

Testimonial: "no."

  • 1 more comment 
  • shyboy67362
    shyboy67362 Feb 06, 2014

    Stuck key on the keypad? how do I reset it? I shut down the circuit breaking for 2 days just to see if that reset,but no help.

  • RonW
    RonW Feb 06, 2014

    Per tech sheet for this model will not start or run and above key(s) is flashing rapidly stuck key(s) or shorted circuit (s) on keypad in keypad, shorted connections or circuits on control panel that read the keys this tech sheet should be attatched to the panel under dishwasher door

  • RonW
    RonW Feb 06, 2014

    Sorry there is no reset

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Kenmore Ultra Wash Dishwasher LIghts are blinking....

I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Posted on Mar 22, 2008

SOURCE: Kitchenaid Dishwasher Control Panel lights - some don't light up

control panel light all of a sudden do not come on and my unit wont start model kud101fl

Posted on Mar 25, 2008

  • 172 Answers

SOURCE: KENMORE ELITE DISHWASHER - MULTI-LIGHTS FLASHING

Look at your manual, usually available on net for reading or downloading. Blink lights are often used to code out a problem with various combinations and repetition rates to indicate trouble code number for look-up in manual.

Posted on Feb 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brush bar stops rotating when I recline the upright part beyond 45 degrees. Brush bar rotates but if I move the machine too far away, increasing the angle it stops. All cleaned out etc


There is a switch in the ball which is activated as you pull the handle back from the upright position. The lever that activates the switch pivots as the handle rotates backwards. Try to determine if this lever could be broken or mislocated somehow..

May 02, 2016 | Dyson DC40 Multi floor Upright Vacuum...

1 Answer

My Sharp Aquos LC-26D44E-GY in the spare room has stopped working. It worked ok about 2 weeks ago, went to switch it on last night & its dead. We had a thunder/lightening storm last week? Ive changed...


First check your power outlet, try connecting the TV to a different power outlet. Then see whether the LED light on the TV is on or blinking. Anyhow, this might need attention by a qualified service technician.

Jul 15, 2012 | Televison & Video

1 Answer

Carrier Weathermaker 8000 stopped working.


look on the inside of the panel an you will find the diagnostic indications blinks there that will tell you what is going on

May 23, 2010 | Heating & Cooling

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

Back door on my 1990 Toyota Camary will not open from inside or outside door handle,door is unlock.


door handle linkage has come loose. possibly linkage securing clip has broken. need to remove inside door panel somehow reach inside door and open it then you will be able to continue making repairs. good luck. not easy. but it can be done.

Mar 21, 2010 | 1990 Toyota Camry

1 Answer

Driver's side window switch doesn't work.The switch that lowers and raises the driver's side window in my 1998 Toyota Avalon has stopped working. Until last week, it worked sporadically. I think the switch...


i know on some toyotas, you do not need to remove the door panel just the handle where the switch assembly is located...if the panel around the switches is plastic then pry GENTLY up on the plastic to dislodge it from the door handle and inspect connections there...if everything checks out fine, then check fuses...perhaps this was a problem for so long that the window motor finally blew a fuse. if so replace both fuse and motor...if fuses okay, then with a long screw driver locate any screws under the door handle, bottom of the door panel, mirror panel etc, and remove...then gently pry outwards on door panel until it is released. disconnect your harness at the window motor and hook in a test light and operate the switch..if light illuminates, replace motor..if not, then replace switch or switch panel..which ever/.

Nov 13, 2009 | 1998 Toyota Avalon

3 Answers

Door lock problems for 2003 Honda


sounds like the central locking motor is gone

Aug 12, 2009 | 2003 Honda Civic

1 Answer

Same exact problem.


Could be the plunger motor/ vaccum plunger under the hood. If the cruise light is on, the computer thinks it is working.

Jun 25, 2009 | 2003 Jeep Grand Cherokee

1 Answer

Driver door will not open from inside


Your inside door handle is probably broken. The gear has stripped causing it not to work. Remove the door panel to verify the rod for the inside handle is not moving. .

Feb 03, 2009 | 2000 Ford Expedition

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Dishwashers Experts

Mike

Level 3 Expert

4359 Answers

Smitty

Level 1 Expert

240 Answers

Cindy Wells

Level 3 Expert

6005 Answers

Are you a KitchenAid Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...