Quadrant monostem tap installation - Rangemaster Kitchen Ranges

hi
o obtain the MAC address on a CK3X, CK3R,and 70 Series Handheld computer, follow the steps below:

1. Tap the 'Windows' button on the lower left hand corner.
2. Scroll towards the bottom of the Windows screen to the "ISpyWiFi" application and tap to launch it.
3. ISpyWiFi will open up in the ISpy tab.
4. At the top of the screen, look for the 'WiFI NIC' quadrant which displays the MAC address.

you need to replace the gear no shaft on shalf put washer to top of gear

Hi, procedure from autozone.com pasted below. Please let me know if you have any questions, and thanks for using FixYa.

CAUTION The clutch driven disc often contains asbestos, which has been determined to be a cancer-causing agent Never clean clutch surfaces with compressed air. Avoid inhaling any dust from any clutch surface. When cleaning clutch surfaces, use a commercially-available brake cleaning fluid.
REMOVAL & INSTALLATION

1. Lift the clutch pedal to its upward-most position to disengage the pawl and quadrant. Push the quadrant forward, unhook the cable from the quadrant and allow it to slowly swing rearward.
2. Open the hood and remove the screw that holds the cable assembly isolator to the dash panel.
3. Pull the cable through the dash panel and into the engine compartment. On 5.0L engines, remove the cable bracket screw from the fender apron.
4. Raise and support the vehicle safely using jackstands.
5. Remove the dust cover from the bell housing.
6. Remove the clip retainer holding the cable assembly to the bell housing.
7. Slide the ball on the end of the cable assembly through the hole in the clutch release lever and remove the cable.
8. Remove the dash panel isolator from the cable.

To install:

1. Install the dash panel isolator on the cable assembly.
2. Insert the cable through the hole in the bell housing and through the hole in the clutch release lever. Slide the ball on the end of the cable assembly away from the hole in the clutch release lever.
3. Install the clip retainer that holds the cable assembly to the bell housing.
4. Install the dust shield on the bell housing.
5. Push the cable assembly into the engine compartment and lower the vehicle. On 5.0L engines, install the cable bracket screw in the fender apron.
6. Push the cable assembly into the hole in the dash panel and secure the isolator with a screw.
7. Install the cable assembly by lifting the clutch pedal to disengage the pawl and quadrant. Then, pushing the quadrant forward, hook the end of the cable over the rear of the quadrant.
8. Depress the clutch cable several times to adjust the cable.

1. First press connect on your console.
2. Then press and hold the connect button on your earpieces for 3 seconds.
3. What ever quadrant you have the controller in will be the quadrant associated with the headset.
4. If you want it to be associated with a controller in another quadrant the press the control button on your headset and it will advance to the next available quadrant.
5. The quadrant selected will be indicated by the number of beeps you hear.
6. When the lights on your XBOX roll around and flash one time then your headset is connected.

• *Note if this is your first time then you need to go to go online at XBOX live to get the latest dashboard update* http://www.xbox.com/live

Regards, Tony

PTS (Plumbing Trade Supplies) are one of the largest suppliers of armitage shanks brassware. Look them up in the phone directory, im sure there will be a store near you. You should be able to order spares from them.

clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:

REMOVAL & INSTALLATION


See Figure 1

1. Disconnect the battery cable from the negative terminal of the battery.
2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
3. Remove the lower dash panel section to the left of the steering column.
4. Remove the shrouds from the steering column.
5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
8. Disconnect all electrical connectors from the steering column.
9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:

1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
7. Attach the clutch cable to the quadrant.
8. Position the steering column onto the four studs in the support bracket and start the four nuts.
9. Connect the steering column electrical connectors.
10. Install the steering column shrouds.
11. Install the brake pedal support lateral brace.
12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
13. Install the lower dash panel section.
14. Install the steering wheel.
15. Connect the battery cable to the negative terminal on the battery.
16. Check the steering column for proper operation.
17. Depress the clutch pedal several times to adjust the cable.

remove gear stick and check its in properly, if you removed the gear shifter quadrant box bolted to top of gearbox you more than likely put it in while a gear was selected, remove and make sure gear box selectors are all lined up in nuetral then refit quadrant box and then gear lever.

hi,

it is located in the lower right quadrant of the board,it was just tapped in the copper shielding for yo to be able to removed it

thanks

LIFT THE CLUTCH PEDAL TO DISENGAGE THE ADJUSTING MECHANISM.THIS MUST BE DONE DURING CABLE INSTALLATION AS FAILURE TO DO SO WILL RESULT IN DAMAGE TO THE SELF ADJUSTER MECHANISM.INSERT THE CLUTCH CABLE THROUGH THE DASH PANEL AND THE DASH PANEL GROMMET.( WARNING ) BESURE THE CLUTCH CABLE IS ROUTED UNDER THE BRAKE LINES AND NOT TRAPPED AT THE SPRING TOWER BY THE BRAKE LINES IF EQUIPPED WITH POWER STEERING ROUTE THE CABLE INBOARD OF THE POWER STEERING HOSE.PUSH THE CLUTCH CABLE THROUGH THE INSULATOR ON THE STOP BRACKET AND THROUGH THE RECESS BETWEEN THE PEDAL AND THE GEAR QUADRANT.LIFT THE CLUTCH PEDAL TO RELEASE THE PAWL ROTATE THE GEAR QUADRANT FORWARD AND HOOK THE CABLE INTO THE GEAR QUADRANT.INSTALL THE CLUTCH SHIELD ON THE BRAKE PEDAL SUPPORT BRACKET.ON THE TEMPO OR TOPAZ INSTALL THE PANEL ABOVE THE CLUTCH PEDAL.USING A PIECE OF WIRE CORD OR TAPE SECURE THE PEDAL IN THE UPMOST POSITION.INSERT THE CLUTCH CABLE THROUGH THE INSULATOR AND CONNECT THE CABLE TO THE CLUTCH RELEASE LEVER IN THE ENGINE COMPARTMENT.REMOVE THE DEVICE USED TO TEMPORARILY SECURE THE PEDAL AGAINST ITS STOP.ADJUST THE CLUTCH BY DEPRESSING THE CLUTCH PEDAL SEVERAL TIMES.INSTALL THE AIR CLEANER.

A two by two grid forms four quadrants. In the upper left quadrant, place a 4. In the upper right quadrant place a 2. In the lower left quadrant, place an eight. In the lower right quadrant place a 5. Horizontally, the numbers 42 and 85 are formed. Vertically, you form the numbers 48 and 25. The sum total of these numbers is 200. 42 + 85 + 48 + 25 = 200.