Question about Behringer DJx700 5-Channel Pro DJ Mixer with Digital Effects & Bpm Counter

Open Question

Behringher djx 750

Cross fader

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do is fix my Numark m6 bleeding cross fader


/it's most likely a defective fader, but before replacing it, get a can of Deoxit5 or fader cleaner and spray inside the fader, then move it the full length os travel about 20 times to see it that clears it up.

Jul 09, 2016 | Numark Music

1 Answer

Djx 750 - no power - transformer dead?


Actually, you may be in luck. A burned cap means that it has done exactly what it's supposed to do. So...you might stick an identical one in there -- it's a 0.1 uF cap, and you can find these at Radio Shack (0.1 uF 50V) or online. They are cheap, so give it a shot.

Feb 16, 2014 | Behringer DJx700 5-Channel Pro DJ Mixer...

1 Answer

Faders not working properly on am844d right channell goes in out when I wiggle the main L/R fader. Some of the channel faders are eractic. The level of volume is not responding right to fader...


You probably wrecked the faders putting De-Oit in them!!! NEVER use that in pot and faders... It is for switch contacts only.
You have ONE chance to save them. From Home Depot get a can of CRC226 in the electrical dept. Put some of that using the spout into each fader near the middle and work the faders. The CRC226 costs about $2.70 a can. Make sure it is the 226 as there are OTHER CRC products there and only 226 is the one that is suitable.

The De-Oxit will have cleaned out the lube of the faders and if you are unlucky, one or more of the wipers will have folded back which is fatal... The CRC226 is an electrical lube that I have restored faders and pots with... It has many other uses including lubing plier joints...

Dec 31, 2010 | Phonic Am 844d Mixer 8 Mic/line 4 Stereo 4...

1 Answer

What is the value of mackie's faiders and master faders


The channel faders will be a 10K with standard fader taper.

The master fader is a 50K dual, with standard fader taper.

Sep 20, 2010 | Mackie 1604 Vlz3 16 Channel Mixer

2 Answers

I think my crossfader stop working for some reason. when im on side B i get sound then i slide over to side A and i still get sound from side be,,, all the assign are right also the bass mid and hi kill...


I suspect one end of the crossfader pot has broken from the element. The fader probably costs less than $5.

You likely will have to remove all the knobs and some screws to seperate the board with the fader from the front panel so you can replace the fader.

VERIFY the pot is bad with an ohmmeter before dis-assembling however.

You MAY be in luck. It looks like the cross fader has a connector which MIGHT allow you to remove it or certainly only a small board for replacement, seeing these take abuse.

It appears that the cross fader is a dual 100K type B taper.

Apr 26, 2010 | Behringer DJx700 5-Channel Pro DJ Mixer...

1 Answer

Hi i have djx 750 and i have connect the master output on my amplifire and the tape or both to my line in from my pc sound card!!! the problem is that when i have open the mic from my mixer i can here it...


i have djx750 mixer, and i want to connect speakers to it,but the cable for the speakers are guitar jack leads and back of mixer are scart can i get a cable with guitar jack and scart on same lead??cheers

Dec 14, 2009 | Behringer DJx700 5-Channel Pro DJ Mixer...

1 Answer

My effects on the behringer djx 700 dj mixer stop working how


This is a wild educated guess.

I repaired a Behringer guitar amp that had a DSP effects in it (BX1200 I believe).

The effects were on a seperate board and the board had its own 5 volt power supply. The filter capacitor for the 5 volt power on the board was UNDERSIZED and it had degraded causing the 5 volts to drop out of regulation, dipping to 4 volts. This caused the DSP effects to fail.

YOUR device MAY use the same DSP OR design.

Check the 5 volt power with an OSCILLOSCOPE to look for dips below the 5 volt operating point that occur at 120 HZ.

Oct 19, 2009 | Behringer DJx700 5-Channel Pro DJ Mixer...

1 Answer

Crossfader Selectors scratchy


The sliders on MOST of the mixer devices are pretty weak. They are subject to dirt or liquid getting into the slot and spoiling them. Fix is to replace them. You usually can find replacements at Digikey or Mouser that are suitable. The parameters are the resistance, the packaing and the length of throw AND importantly the "taper" of the resistance element.

Sep 08, 2009 | Behringer DJx700 5-Channel Pro DJ Mixer...

Not finding what you are looking for?
Behringer DJx700 5-Channel Pro DJ Mixer with Digital Effects & Bpm Counter Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Ben Armstrong

Level 2 Expert

360 Answers

The Knight
The Knight

Level 3 Expert

76100 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...