GE 2-9439 Phone i need the manual to store numbers in one out of the 32 speed dial buttons!

I was unable to locate a user manual for that particular device, however the basic instructions for programming speed dial functions are normally very similar between most phones.


Generally there are ONE TOUCH Speed Dial buttons labelled something like M1, M2, and M3 on the dial pad somewhere.


There should also be another button labelled PROG or STORE on the keypad as well.


Normally to program a number into a ONE TOUCH speed dial memory location you carry out the following procedure:


Lift the handset.


Then press the PROG (or STORE) button.


Now just use the number keypad to dial the full telephone number that you want to store in a Speed Dial location.


Once the full telephone number is dialed, then push the M1 button to store that phone number in the M1 One Touch Speed Dial location.


The phone may or may not show some kind of confirmation that the M1 location was just programmed, then just hang up the handset.


Now when you lift the handset and press the M1 button, the phone should automatically dial the phone number you programmed into it.


Now just repeat the same process for the M2 and M3 One Touch Speed Dial buttons with other phone numbers if necessary.


To change one of the Speed Dial numbers, just carry out the normal programming procedure for that location using the new phone number and the old number will simply be overwritten.


I truly hope that was helpful to you.
Good luck and take care.

Joe.

1. Pick up the handset.
2. Press the store button.
3. Press the memory location (0-9) to be erased.
4. Press delete for three seconds until the number in the display is erased.
5. Hang up the handset.

If you need a manual, you can download one at
http://www.home-electronics.net/ge/pc/IB/29267GE1_IB.pdf

After a lot of research, I have found that GE has handed the phones and their manuals down to a company called "ThomsonTM" And if you come across any of problems for this phone in the future, I'll give you their phone number so you can still get help, at: 1-800-447-1700

Otherwise for help right now for the speed dial issue, I could only find directions that were of general use of multiple GE Cordless Phones, so it's worth a shot if you've got the time, otherwise, I suggest calling the number above.

Here is goes:

1.)Raise the phones reciever, or push the "Power/On" button.

2.)Press the "Store" button.

3.)Press the number 0 through 9 or a quick dial letter A, B, C,... to assign, then press the "Store" Button again to confirm the entry.

4.)Enter the number you want to assign the speed dials memory location, and press "Store".

5.)If your GE Phone prompts you to enter a Contact Name, use the keypad to enter it. Press the "Skip" button to enter a space, and the "Store" button to confirm your entry once again.

Once again, this is just a generalized GE Cordless phone guide, and may not be exact to your phone, in which I further suggest calling the electronic product's helpline by ThomsonTM at:
1-800-447-1700 begin_of_the_skype_highlighting

Hope this helps!
Remember to give me 4 Thumbs Up
for all the hard work to the Community! :D
~~Dayminner

You will need the model number. They might have the manual at this link
http://www.home-electronics.net/ge/pc/user-manuals.asp

The manual from the GE web site is here:

http://www.home-electronics.net/ge/pc/IB/29267GE3_IB.pdf

It's a pretty straightforward process, Pick up the handset press STORE a location (0-9) STORE dial the number STORE

With only 10 storable numbers it's pretty thin, but you also have the last 50 CID numbers to dial. If you live in an area with more than one local area code (overlays) and mixed 10 digit dialing, it looks like you may have some programming to do to make it dial CID numbers properly.

Carl

Hello,
Here are the commands to run the phones memory dial (speed-dial).  I have included the instructions for deleting and changing numbers as well.  It is listed below.  I hope this helps you out.
Ken

MEMORY DIAL INSTRUCTIONS Store up to ten 20-digit numbers in memory for quick dialing. Storing a Number in Memory 1. Make sure the phone is OFF (not in TALK mode). 2. Press the MEMORY button. 3. Press a number (0-9) to store the dialed number in that memory location. 4. Press the MEMORY button again. 5. Use the handset number keypad to enter the telephone number (up to 20 digits, including pauses) and press the MEMORY button again to save the number. The unit beeps to confirm. 6. To enter another number in a different memory location, return to step 1 and repeat the process.
Storing a Redial Number 1. Repeat steps 1 through 4 in Storing a Number in Memory. 2. Press the REDIAL button. 3. Press the MEMORY button to store the number. You will hear a confirmation tone.
Changing a Stored Number 1. Repeat steps 1 through 6 in Storing a Number in Memory. 2. Press the MEMORY button to store the number. You will hear a confirmation tone. The old number will be overwritten with the new number.
Dialing a Stored Number 1. Make sure the phone is ON by pressing the TALK button. 2. Press the MEMORY button. 3. Press the number (0-9) for the desired memory location. The number dials automatically. Inserting a Pause in the Dialing Sequence Press the PAUSE# button once to insert a delay in the dialing sequence of a stored telephone number. A pause is needed to wait for a dial tone (for example after you dial 9 for an outside line, or to wait for a computer access tone). Each pause counts as 1 digit in the dialing sequence. If you need a longer pause, press the PAUSE# button twice.
Deleting Stored Numbers 1. Press the MEMORY button. 2. Press the desired memory location (0-9). 3. Press the MEMORY button twice to delete the entry. 4. You will hear a confirmation tone.

Hi,

If you go to the following webpage there is a link to the manual:

http://www.amazon.com/exec/obidos/ASIN/B00005NGRJ/plaza101-20/ref=nosim/

It is under the 'Product details' section. The section on managing the memory start on page 34.

To change a stored number you just follow the initial instructions, namely:

1. Press the STORE button. ENTER TEL. NO. is displayed.

2. Use the keypad to enter the phone number. If you
want to add spaces instead of dashes in the number,
it will dial correctly.
• To scroll forward or backward, use NEXT or
PREVIOUS.
• To erase the current digit, press ERASE.

3. When finished, press STORE. ENTER NAME is
displayed.

4. Use the keypad to store a name (up to 16 characters).
More than one letter or character is available in each
of the number keys. For example, to enter the letter
“A,” press the 2 key once. For a “B,” press the same
key twice. For a “C,” press it three times.
• To add a space, press NEXT.
• To scroll forward or backward, use NEXT or
PREVIOUS.
• To erase the current digit, press ERASE.

5. When finished, press STORE. MEMORY LOCATION is
displayed.

6. Press the memory location number (0-9 or A, B, C) to
store the number.

I hope this helps you.

Here are the quick instructions on how to program the phone numbers.

You can also download a copy of the User's Guide from: http://www.retrevo.com/search/v2/jsp/downloadPage.jsp?doc=c96e9c823d0df43989039e5385bef04a&q=GE+29322GE1

Just enter the 4 digit captcha code and you will be able to download the User's Guide.

Please let me know if yo have any questions.

Good Luck!
++++++++

STORING A NUMBER IN MEMORY
To program priority keys:
1. Make sure the telephone is properly installed. Pick up the
handset and listen for the dial tone. If you don’t hear the
dial tone, recheck or repeat the installation steps.
2. Press the SPEAKER button or pick up the handset.
3. Press the store button.
4. Dial the number to be stored.
5. Press the store button again.
6. Press the A, B or C button.
7. Press the SPEAKER button or hang up the handset.
To program frequently called numbers:
1. Press the SPEAKER button or pick up the handset.
2. Press the store button.
3. Dial the number to be stored.
4. Press the store button again.
5. Press one of the 10 memory location buttons 0-9.
6. Press the SPEAKER button or hang up the handset.

1 - Lift the receiver and get the dial tone.
2 - Hit 'Store'
3 - Enter the number you wish to store in the phone
4 - Hit the store button again
5 - Hit the memory button you wish to store the number into
6 - Hang up!

This should store the number wherever you want to put it. Remember if you want to store it in one of the 'lower' positions (second line of the memory index card) push the 'Shift' button before you push the memory button for that location.

Emergency/quick dial numbers: Pick up handset, push store, enter the phone number (it will not call the number), push store again, Push A,B or C. hand up handset. Frequently called numbers, pick up the handset, push store, enter the phone number, push store again, push key pad 1, or 2, etc. for memory location. Hang up handset. How to change a stored number. just repeat the sequence. How to clear a stored number, repeat the storage skip step 3 (do not enter the phone number). How to correct an error while storing, just hang up and repeat.