Question about Sony STR-DE425 Receiver

Open Question

No power to receiver - Sony STR-DE425 Receiver

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power how to solve


Check outlet for power by plugging in a known working device to the outlet. If it has power, replace the power cable of the receiver. IF that still does not work, the receiver's power supply is dead.

Jan 21, 2016 | Denon AVR-1906 Receiver

1 Answer

How to power up av receiver


Connect the AC power chord provided with the Receiver and switch-on power - the standby indicator glows now press the standby switch to power on your receiver

Jun 20, 2015 | Yamaha RX-A1020

1 Answer

My receiver (new) will not turn on? Is there a reset button?


There isn't a reset on these receivers.

If it doesn't show a power light on it, then try disconnecting the power for 30s.
If still no power light
  1. check the outlet it's connected to
  2. disconnect all cables from the back of the receiver but power and try again.
  3. connect the receiver to a different outlet (still with nothing else connected)
if you still don't get a power light on it then the receiver is dead.

Jul 03, 2014 | DISH Network ViP 211 DTV Receiver

1 Answer

SLINGLOADED RECEIVER TRIPPING OFF


Beverly Gobin,

It sounds like the receiver may be power cycling. Try bypassing any power strips or surge protectors and plug directly into a wall and try again. If the problem continues, if possible try another outlet.

Send me an email at thomas.faust@dish.com if the problem continues since the receiver may need to be replaced.

Tommy Faust
DISH Social Media Representative

Mar 08, 2012 | DISH Network ViP 922

1 Answer

When pressing power on button, power light comes on for 5-10 seconds, then goes off. Will not stay powered up....


Hi t53doc,this is Mike Houston of DISH Network I was reading over your post and see wherethe receiver will not stay powered on. Please unplug the receiver for 10 seconds andthen make sure the receiver is plugged directly into the wall. It will power upand require the signal and download the program guide. If you have any questionsI will leave my e-mail michael.houston@dishnetwork.I will leave a link to help with these steps. http://www.dishnetwork.com/SupportSection/receiver-no-power

Mar 27, 2011 | DISH Network 301 DTV Receiver

1 Answer

My receiver's Power light comes on when I aply power to the receiver but after 5 seconds goes off. Why?


dave2551,

When the receiver is rebooted, the power light will come on and then go out. This is normal. After several seconds the power light will illuminate again and it will acquire satellite signal. Again, when power is removed and restored to the receiver, it is normal for the green power light to go out and then illuminate again. I hope this helps.

Ray Calo
DISH Network - Executive Offices

Aug 07, 2010 | DISH Network 311 DTV Receiver

1 Answer

When i push power button clicks on immediately


I had this problem also and discovered an easy way to trick it into powering on: Click the power button, then within 1 second of the receiver powering off, click the power button again. The receiver should stay on this time. This works with both the button on the receiver and the remote control.
I would like to know what causes this problem and whether or not I should be concerned about damage being done. I assume this is a power protection. I haven't tried plugging this receiver into a different power socket to test, but I don't think the power plug is the problem. Note: I have the subwoofer plugged into the power plug on the back of the receiver.

Feb 23, 2010 | Onkyo HTR500 Receiver

1 Answer

How do I hook up a non powered sub woofer on my htr-5630?


You will need an amplifier or 2 channel receiver. Hook the sub out rca jack to the rca inputs on this new amp or receiver and hook the speaker terminals on sub to speaker terminals on same amp or receiver. Your Yamaha receiver doesn't have any power for a passive sub.Just pick up any old fairly high powered receiver for fifty dollars and you're good to go.I use old dolby pro logic receivers as they are a dime a dozen today. Good luck.

Feb 20, 2010 | Yamaha HTR-5630 Receiver

1 Answer

Vip211 will not power up, no green light or signal?


Hi johnmcmillan with thereceiver not powering up we can try a few things to get the power on. Firstthing you will want to do is make sure the receiver is plugged directly intothe wall. If the receiver is plugged into the wall and the green light is noton you can do a reset by unplugging the power cord from the receiver for 10seconds and plug it back in. I will leave a link to help with this. http://www.dishnetwork.com/SupportSection/receiver-no-power

Oct 17, 2009 | DISH Network ViP 211 DTV Receiver

1 Answer

Receiver won't power on


My receiver was turned on and plugged into a surge protector along with my LCD TV. The power went out and everything shut down.

Dec 28, 2006 | Pioneer VSX-D514 Receiver

Not finding what you are looking for?
Sony STR-DE425 Receiver Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sony Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...