Question about Maytag EPIC MFW9600S

1 Answer

Control lock stays on

Control lock light stays on machine will not start i tried unplugging the machine still no result

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 111 Answers

Try holding for 3-5 seconds should unlock controls.

Posted on Jan 24, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
SolutionGuy
  • 331 Answers

SOURCE: Maytag front load 9700

First things first... please follow this link to see if your machine is part of Maytag's recall... http://www.washerrecall.com/ or this site for details on the recall... http://www.cpsc.gov/cpscpub/prerel/prhtml07/07135.html

Posted on Aug 19, 2007

KevinWhite
  • 1902 Answers

SOURCE: control locked light on - machine will not

Hello

To unlock the controls press and hold the END OF CYCLE button for 15 seconds, the problem should be resolved after doing this. Please get back to me if you have any other questions.

Kevin

Posted on Nov 15, 2010

Testimonial: "This WORKED! I was just about to call a repair man. This probably saved me at least $100"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool Cabrio HE washing machine will turn on. After you hit start, it will try to sense the load and immediately turn off with the lid lock button on. The lid lock button does not blink. It just stays...


Sounds like a sensor is detecting something wrong and won't start the cycle until it senses all is well. Try checking that the door is closing properly. If the door sensor thinks the door is open, it can cause machine not to start cycle. Or check that the lower filter element is not clogged. Usually in the bottom of the front on the left or center of the machine is a little door that hides the filter screen for the drain. It should be cleaned periodically. Being clogged can cause issues. Hope this helps.

Oct 22, 2018 | Whirlpool Washing Machines

1 Answer

Maytag front load 9700


First things first... please follow this link to see if your machine is part of Maytag's recall... http://www.washerrecall.com/ or this site for details on the recall... http://www.cpsc.gov/cpscpub/prerel/prhtml07/07135.html

Aug 19, 2007 | Maytag Neptune MAH9700 Front Load Washer

Tip

The front light lit on my Whirlpool dryer is showing control locked


Hi.

If the front light lit is control locked, that means that your Whirlpool electric dryer had been set in control lock mode.

Control lock is a special mode that will prevent user from changing settings or using control until the dryer gets unlocked again.

The machine is set to control lock mode by holding down the CONTROL LOCK/UNLOCK button for several seconds. In the same way you can stop the control lock mode when the machine is already set to Control Lock.


When the dryer is running and Control Locked is on, the dryer can still be stopped by pressing the Pause/Cancel button, but cannot be restarted until the control is unlocked.

If the front light lit is control locked but the dryer door opens and it does not turn off, then you are probably in this situation. In that case, the door will be opening , but the machine still stays locked.

Disconnecting the machine from power, either unplugging power cord or tripping circuit breaker, won't help. The control lock system is designed to stay on in case of power failure.
If the machine is control locked, try unlocking it with the following procedure.

To unlock: Press and hold the CONTROL LOCK/UNLOCK button for 3 to 5 seconds to turn the control lock feature off.

If that does not work, try disconnecting power for five minutes to reset the machine, and eventually do unlock again. As said, cutting power alone will not cause the machine to unlock.


If the machine is still not responding, the lights stay on all the time, the dryer panel does not respond to control unlock procedure, and the door does not lock anymore, then it may be a defective control board.

If you are in this situation, before replacing the control board more parts, including the door lock must be tested. In that case the best option may be contacting the Whirlpool support number listed on the Dryer use and care manual, usually in the last pages.

In this case try resetting control lock as explained above, as told the dryer is more likely control locked and then stopped.


Regards.

Ginko.

on Feb 01, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

Why the lid locking led is blinking after lock the lid and stay standby with out working ?


The unit will not operate in this condition until the lid lock signals a locked condition. The controller is signaling that it believes the lid is not locked. Assuming the lid is actually locked, then this might occur because of a bad wiring connection (check the lid lock switch assembly and the cabling at the controller) or a bad lid lock switch/sensor.

Dec 05, 2014 | Maytag Washing Machines

2 Answers

How to correct control locked will not go off on whirlpool ghw9150 washer


While the machine is 'on' press & hold the "end of cycle" button for 3 seconds, or till the lock light goes off. This is on the far left or right of the machine's panel. Good luck! Pl rate me.

Sep 01, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore HE Washer Model 11046472501 - add a garment light stays on with the door lock light on at the same time. We have unplugged the machine and ran the drain and spin mode, but he washer won't


Not sure if these will help or not:

http://www.youtube.com/results?search_query=Kenmore+HE+Washer+diagnostics&oq=Kenmore+HE+Washer+diagnostics&gs_l=youtube.12...4054.11443.0.13769.12.12.0.0.0.0.236.2449.1j0j11.12.0...0.0...1ac.1.93rgz26enSw

Jan 26, 2013 | Kenmore Ap4327152 Motor Control Board for...

1 Answer

Door won't open. door locked light stays on. I


Hi,


Press and hold the End of Cycle Signal button for three seconds. This will turn off the Control Lock feature.


Thank you !!

Jul 27, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Control lock light stays on nothing else happens what could i do


Those locks are on a timer that until the wash is complete it does not unlock the unit.
Unlike a normal washer where you can open it at any time and throw in some cloths you may have forgot, this one seems to take up to to minutes after you stop the unit mid wash.
If it is taking more then the 2 minutes then the door lock may be faulty, try unplugging the unit then plugging back in, do not force the door open as this will result in a broken switch.

Good Luck!

I’m happy to help further over the phone at https://www.6ya.com/expert/michael_341f3f9dee622e54

Nov 14, 2009 | LG WM2277H Front Load Washer

2 Answers

Control locked light come on and stay on, machine not running


take a good look and read on your control panel i don't remember which button you need to hold for 3 or 5 second to lock unlock control panel. it is also called child lock system.

May 21, 2009 | Whirlpool Duet 3.8 cu. ft. Front Load...

Not finding what you are looking for?
Maytag EPIC MFW9600S Logo

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...