Need to find a master link

Hello Helen, I am sending you the link to download the user manual of your Teac Clock Radio CRX25UBT
I hope you can enjoy
Greetings Franco Dosil

Hola Helen, te estoy enviando el link para que descargues el manual de usuario de tu Teac Clock Radio CRX25UBT
espero lo puedas disfrutar
Saludos Franco Dosil
http://www.teac.com.au/downloads/product_downloads/CRX25UBT_IM_new.pdf

Troubleshoot steps on following link:
http://waterheatertimer.org/How-to-troubleshoot-timers.html#digital

You will need to find a local Sewing Service Centre and see if they can help....I don't even know what continent you are on !!
I stopped taking new servicing orders end of last week to get clear for Christmas....borrow a machine if you need to, but DO NOT use with a faulty switch.

I am not familiar with the Kett Car but I'll assume you've tried to see if there was an adjustment of some sort and you couldn't find one....So have you tried removing a link of the chain to shorten the chain? Chains can be shortened by taking one link out. Just realize that if you remove a link the chain may then be too short. So I'm not sure how much slack you actually have?
But to remove a link:
1) Find the master link where there will be little clip on the outside of one side of the chain and remove that clip and save it. It should slide off with a little pressure.
2) The Master link with the clip removed (mentioned above) can be taken out and the chain will no longer be in a loop. Save the master link because you'll need to put it back together after.
3) To remove a link, using a file or a grinder...grind off the last link on eather side of the chain. Use your Master link to see how far or how many links you'll need to remove. Remember, the master link will have to go back in to make the chain a loop again so you want to remove the link in the right place and not remove any more links than you need to.
4) Once you find where you want to remove the link, If you can visualize the letter "H" as a chain link, where the cross bar is there will be a silver piece on each side of the outside of the chain. This is what you want to grind off just on one side of the chain.
5) You'll see how the chaing is put together and using a punch, you can tap out the center cross piece. What you should be left with is (if I could put these sideways it would be easier to show) an 8 on one end of the chain and an 8 on the other side.
6) The master link will go back into the ends of these and rejoin the chain. Master links and chainds can be bought at most hardware stores so if you cut off too much you can replace the chain or master link.
7) If you do need to get a new chain, take the old one with you so you can get the right size.

I got mine for Christmas (2010)... Worked fine the first week or two... Then I noticed that it doesn't get hot at all anymore... Thought maybe my husbands side controlled both (like a master safety)... Since he sets it at 3... Mine is set on 'high'... But no, put his on high, it gets super hot, my side barely warm.

Enter your last 4 digit of your cell # to unlock

Here is the software download link




http://download.service.mattel.com/us/technical/Easylink_update_v1.3.0.2.exe

you will need to smash the rivets or you will loose the link for sure. It takes a special tool that I'm sure you don't have. The correct master link should be available locally. I have just checked our inventory and can only find the clip style links. If we sent you the rivet style it must have been the last one. We have plenty clip style links here but Tuesday is the best we can do now for shipping. I apologize for not sending the clip style. I'll check on how that happened.,

you will need to smash the rivets or you will loose the link for sure. It takes a special tool that I'm sure you don't have. The correct master link should be available locally. I have just checked our inventory and can only find the clip style links. If we sent you the rivet style it must have been the last one. We have plenty clip style links here but Tuesday is the best we can do now for shipping. I apologize for not sending the clip style. I'll check on how that happened.,

Download adobe reader (Free) if needed
button appears on the following links
http://www.adobe.com

Manual Link
http://www.sandisk.com/Retail/Default.aspx?CatID=1304

Sorry not familiar with using itunes, myself