Maytag MAH6500 Neptune Front Loading Washer w/Built in Water Heater Logo
Posted on Oct 22, 2007
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

MY NEPTUNE MAH4000AWW WORK WHEN IT WANT TO WORK

THE MACHINE FILLS WITH WATER THEN STOPS, HIT THE START BUTTON IT START AND STOP AGAIN. IF I ADVANCE THE TO THE NEXT SETTING AND STOP AGAIN BUT WHEN I ADVANCE IT TO THE RINCE CYCLE IT RUNS STRAIGHT THROUGH THE WHO CYCLE NON-STOP.  BUT SOME DAY IT JUST WORKS WILL NO PROBLEMS FOR ABOUT AWEEK OR TWO STRAIGHT

Answer This Question
  • Anonymous Nov 08, 2007

    We have the same problem! It's so frustrating!! As soon as I push the start button and turn to walk away, it stops. The display panel says it's experienced a power failure, but the power is still on and the machince comes back on when I push the start button. After pushing the start button and stopping another 15 times, it will finally finish the cycle.



    I certainly hope someone figures out what's wrong!

×

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

  • Expert 146 Answers
  • Posted on Nov 05, 2007
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
MVP:

An expert that got 5 achievements.
Governor:

An expert whose answer got voted for 20 times.
Scholar:

An expert who has written 20 answers of more than 400 characters.

Joined: Oct 13, 2007
Answers
146
Questions
1
Helped
100770
Points
223

Sounds like you have an intermittent problem with the board or one of the on board switches.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Maytag Neptune MLG2000AWW-works EXCEPT-washer will not stop unless manually turn off. After cycle will sit in OFF with the ON light still on. After 2 minutes, timer advances and start over again.
The replacement timer has failed.
Read full answer
Mar 29, 2022 • Maytag Washing Machines
0helpful
2answers

Won't spin or drain, have tried to rerun cycle and checked drain hose
Check pump / outlet filter , refer to instruction book , clean and replace then re- try
Read full answer
Nov 01, 2009 • Maytag Neptune MAH5500B Front Load Washer
2helpful
3answers

My Maytag Neptune MAH4000AWW will not finish a full cycle.
I had the same problem. I called customer support and they gave me these instructions:
Shut off the water supply to the machine, disconnect the hoses from the back of the machine. Pull out the hose and pull out the little screens and clean them with water or soak in vinegar. I was skeptical but did this and the results were amazing. Apparently if the screens get even a little "gunked" up (my screens really didn't look that bad) the machine senses the change in water pressure coming in and shuts it off. Hope this helps!
Read full answer
Jan 26, 2009 • Maytag Neptune MAH5500B Front Load Washer
0helpful
1answer

Maytag mah4000aww trys to spin shakes and stops
there are off balance switchs on the tub that will turn it off But if the pump sump is full it will pump slow and throw it off balance so check to see how well and fast it is pumping the water out
Read full answer
Nov 30, 2008 • Maytag Neptune MAH5500B Front Load Washer
0helpful
1answer

Maytag neptune front loader, model# MAH4000AWW PROBLEM: Water will not fill. First hot stopped working a few months ago, then cold also stopped. We live a long way from nearest repairman, so have put this...
It sounds like you just have a clogged or bad valve. Depending on the water source I have seen many times a load of crud on the screens where the hose meets the valve. Try taking the hoses off making sure their clear, then inspect the inlets to the valve to see if there is a clog. Unfortunately some of this dirt may have entered and fouled the valve itself, in which case it will need replacing.
Read full answer
Oct 22, 2008 • Maytag Washing Machines
0helpful
3answers

Maytag washer shutting off on rinse cycle
Hi there,

If the washer is not completing the Rinse cycle there may be problem with:

Lid switch
Motor coupler
Belts
Clutch
Drive motor
Drive pulleys
Transmission
Agitator

Let me know if you need further assistance.


Regards
Ellin
Read full answer
Sep 26, 2008 • Maytag Neptune MAH5500B Front Load Washer
0helpful
1answer

Washer Maytag Neptune
Most likely the motor control unit, the MCU controls the timer (loop circuit). Best way to check is to just pull the MCU out and visually inspect it for burned components, although it is not always visible. You may need to make some involved voltage readings to verify.
Read full answer
Sep 22, 2008 • Washing Machines
0helpful
1answer

Maytag Neptune MAH4000AWW
email me at [email protected] also it may not be the motor matags had a promblem with a resistor burning out on the control bd on your mail put maytag motor as the topic and will reply
Read full answer
May 21, 2008 • Maytag MAH6700AWW Neptune Front-Load...
0helpful
1answer

MY NEPTUNE MAH4000AWW WORK WHEN IT WANT TO WORK
Check for low water pressure. Clear screens in inlet valve. Do-not remove screens. This unit will turn off if not filled in specified time.
Read full answer
Nov 08, 2007 • Maytag MAH6700AWW Neptune Front-Load...
11helpful
1answer

Nf pops up on the screen & the washer stops
The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you.
Read full answer
May 13, 2007 • Maytag Neptune MAH5500B Front Load Washer
Not finding what you are looking for?

View Most Popular

MAH6500 Neptune Front Loading Washer w/Built in Water Heater

  • Washing Machines

Related Question

Maytag Neptune MLG2000AWW-works EXCEPT-washer will not stop unless manually turn off. After cycle will sit in OFF with the ON light still on. After 2 minutes, timer advances and start over again.

  • Maytag Washing Machines

Related Topics

190 views

Ask a Question

Usually answered in minutes!

Popular Questions

Maytag Neptune Error COde "nd"

Maytag Neptune MAH9700 Front Load...

My maytag neptune front load washer won't spin all the water out

Maytag Neptune MAH5500B Front Load...

Model FAV6800AWW will not pump water out if clothes are in machin

Maytag Neptune FAV6800AW Top Load...

Fabric Softener Won't Dispense

Maytag Neptune MAH6700A Front Load...

HOW TO FIX NF CODE IN MAYTAG WASHING MACHINE

Maytag Neptune MAH5500B Front Load...

Top Maytag Washing Machines Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

john h

Level 3 Expert

29494 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
MAH8700WWW.pdf. user-manual-MAH6500...

MAH6500 Neptune...

Loading...