I need a manual for my Fujitsu air conditioner

1. Turn off the air conditioner: Before attempting to remove the front cover, ensure that the air conditioner is switched off to avoid any potential hazards.
2. Locate the release buttons: Look for the release buttons on the sides of the front cover. They are usually located towards the bottom of the cover.
3. Press the release buttons: Using your fingers, press the release buttons inward towards the center of the unit. This should release the front cover from the main body of the air conditioner.
4. Gently remove the cover: Once the release buttons have been pressed, the front cover should come loose. Carefully lift the cover upwards and away from the unit.
5. Clean or maintain the unit: With the front cover removed, you can clean or maintain the air conditioner as required. Be sure to follow any instructions provided in the user manual or by a professional technician.

Note: The specific steps to remove the front cover from a Fujitsu ASTA12LCC air conditioner may vary depending on the model and unit installation. It is always best to refer to the user manual or consult a professional technician if you are unsure of the process or need additional assistance.

https://www.manualslib.com/manual/521325/Fujitsu-Remote-Control.html


http://homeappliance.manualsonline.com/manuals/mfg/fujitsu/fujitsu_air_conditioner_product_list.html Free Fujitsu Air Conditioner User Manuals ManualsOnline com

This link should help.
Bob

https://www.google.com/url?sa=t&source=web&rct=j&ei=4qyoVLbJAYWlgwS3h4DwDQ&url=http://www.climatecenter.co.uk/wcsstore/ClimateCenter/Attachment/downloads/fujitsu-trouble.pdf&ved=0CCkQFjAE&usg=AFQjCNGUVY4GRa6K80m-vrUoCoZYWnFlkg&sig2=4ZgQjbhZQoB6A5vASs

Hi,

Most of the time with those units... you have a refrigerant leak...

They also usually have led's that blink to give you a code as to what is wrong...
the blinking can be on the indoor unit or on the circuit board of the outdoor unit...


Here is a tip about troubleshooting your air conditioner...

There are many things that can cause your air conditioner not to cool...

Air Conditioner Trouble - Review the Possibilities

heatman101

Hi,

Here is a tip about troubleshooting your air conditioner...
There are many things that can cause your air conditioner not to cool...

Air Conditioner Trouble - Review the Possibilities

heatman101

Switch on by pressing ON/OFF. Press mode button to cool position. for cool and keep required temp by clicking

Same procedure for Heat. For heat keep +29 and for cool 25 to 22 degree. Press fan for High, Med,Low. If you keep mode in Auto cool and the fan speed will be low and you can't change fan speed.


Please visit Fujitsu website for further details. Hope my msg is helpful?

Hi,

Here is a tip about troubleshooting your air conditioner...
There are many things that can cause your air conditioner not to cool…

Air Conditioner Trouble - Review the Possibilities

heatman101

press snow flake or sun. press flames or cool wind. press heat or cool. press system button several times.

Yes i can! The mode of operation (MASTER CONTROL)has been set to AUTO instead of HEAT. Easy mistake and very simple to fix. Press the MASTER CONTROL button until HEAT is display on the LCD.
I hope that this helps
I take the time to answer you questions so please rate me
Thankyou
Mat

Check if the remote control if still good, using the camera of your cellphone point remote control to the cellphone camera and press the "on" button of your remote and you can see the light emitting from your remote control transmitter. If the lights emits that means your remote control is good, if not means the remote control is defective.If the remote control still good try to press the RST or RESET button on your remote control and try. If wont works it means that the reciever board in the indoor unit is defective.