F35 code appears, even after changing the steam chamber.

If you find a tear in the hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor.
Jul 21, 2015

What is the error code F-35 - Kenmore Elite HE3 Washing ...

Replace the parts, or block the hole with waterproof epoxy putty.

Model # 11047789701 Official Kenmore Elite washer

Sears PartsDirect https://www.searspartsdirect.com > model > kenmore-e...
Here are the diagrams and repair parts for Official Kenmore Elite 11047789701 washer, as well as links to manuals and error code tables, if available. Continue .

..

Unfortunately you spent money unnecessarily, and before making any additional errors; it would be best to have a trained technician with knowledge of the washer, service the system.

Hi, we also got the SUDS error followed by F35 many times. I replaced the analog water level switch, Wirlpool part number W10156252, and the problem went away. The part is located against the back right corner of the top of the washer after removing the top cover. The part cost $62.99 + $12.95 express shipping from ApplianceZone.net. I have the Kenmore HE3t Steam Washer, model number 110.46752 700 front loader. I was able to run about 6 loads of laundry by unplugging the washer, waiting about 5 minutes, the re-plugging and re-starting the washer. Thereafter, the problem became permanent. I always used HE detergent. The washer was purchased new in December 2007, and the I made the repair in September 2009. I spent about $1300 for the Kenmore H3t Steam Washer, and I am disappointed that it required repair after less than 2 years. My mothers old Maytag washer lasted more than 15 years, and was not susceptible to soap SUDS.

F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.@#$%

F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.^@$$

I got the f35 and suds code repeatedly and my clothes weren't washed, I ordered from Sears the analog pressure switch that regulates the water coming into the washer and the codes went away, the part is esitmately $125.00 including shipping but you have to order from the Sears parts department.If you print a diagram of the washer it is #38 in the diagram and is easy to replace. You can install it yourself and as a female I did not call service to do it.

F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Washers n dryers usually require some balancing after a move to the new area, and when you lift the washer on a dolly, you lift it from the rear. Assuming you've already tipped the washer slighlty to one side, checked the bottom for which side has the most metal underneath. This is best done with 2 people. Do the same with the dryer. The braces are used to help balance or to keep from tipping when the machine was packed inside a large box.

suds is determined using the level sw located on top right rear side. remove top cover to see. most letter codes do convert to a f code. most common reason for suds error is use of standard detergent or too much detergent. running a empty load of fabric softener can clean the system. or rinse/spin with nothing. other common problem is this is a whirlpool product.