Base number How do I find out what my base number is please.

Question edited for clarity and funky punctuation.

Check out the link

https://www.google.com/search?q=Astatic+D104+T-UG8+base+to+Uniden+President+Washington

..

From Manual:
To check whether a handset is registered, make sure mains power to the
base unit is switched on and the handset is within range. The handset's
display should show its number and the <Antenna icon> should be steadily
on. If the display shows
again using the following process:
1. On the base station, press <MENU/OK> and <UP/DOWN> to show
REGISTRATION, and then press <MENU/OK> to put the base station into
registration mode. The base display will show "PLEASE WAIT" and the
base will stay in registration mode for about 2 minute, so the following
handset sequence must be completed within this time.
2. Press <MENU/OK> and <UP/DOWN> to select REGISTRATION.
3. Press <MENU/OK> to display PIN?----.
4. Enter the 4-digit system PIN (default is 0000).
5. Press <MENU/OK> to confirm, and the display will show
PLEASE WAIT flashing.
If the handset registration is successful, the display will change to standby
mode with the new handset number and the <antenna icon> will stop flashing.
The handset will automatically be allocated the next available handset
number. If the handset registration is unsuccessful, the <antenna icon> will
still flash

Please mention what kind of base you are talking about, wall hanger or flat floor base?
Furthermore, as you mentioned you dont know the model number, I would prefer to measure the base screw holes (on your TV) and make / design your own custom made base for your TV.
Or measure the hole-to-hole dimension (on your TV) and go some nearest Shopping mall, you can found a separate base (but before going to purchase make sure its matching your TV as you measured), which you can found easily, and buy one.

Please see the screen captures below.
To set the base in Main.




To convert from one numeration base to another, use the baseConvert( command found in the catalog (cat)
baseConvert(number to convert, current base, expected base).
The number to convert must be positive integer (digits 0 to 9 and/or A to F). The current base and expected base can be any positive integer between 2 and 16

Try accessing this website: http://support.asus.com/download/options.aspx?SLanguage=en&type=1 and search using the product serial number. If you are not sure where to get the serial number reffer to the following image:Notebook

1. Please check the base of your notebook for sticker label. (10 characters)
2. The serial number is listed directly below the barcode after the word "SN:".

1. Please check the base of your notebook for sticker label. (15 characters)
2. The serial number is listed directly below the barcode.

Hi,


This is because the extra handset might have not been registered with the base unit.The headset should be register to use the headset with that base unit.

To register the handset to base unit please follow the instruction:-

On registration the handset is allocated a handset number for use on the new base unit, the handset numbers are 1-5.

1. Press and hold
on the base unit until starts flashing. Registration mode will remain active for approximately 3 minutes.

2.Press and hold both
together until you hear a long beep.

3.Select the base unit you wish to register by pressing the corresponding number button 1-4.
4. When PIN is displayed, enter the units PIN number (0000 for this model).
5. If the registration is successful the handset will return to standby mode in a few seconds.

Thanx

please enter a phone number which can readautomated msg. i think your mobile operator is CDMA based. so that you cant get confirmation code.
please submit a GSM based mobile number to facebook..

You need a binary to hex converter. Go to this link to learn all about it. http://www.unitconversion.org/numbers/base-2-to-base-16-conversion.html

Press MODE 4 to enter the BASE-N mode. If the display doesn't say Dec, press SHIFT DEC (the x^2 key) to set base 10. Enter the number to convert. Press SHIFT BIN (the log key) to switch to base 2.

Each time you switch the base the current value is redisplayed in that new base.

Could you post the model number please. There is no reference based upon the number you posted. It will be easier for me to cross reference based upon the model.

Thanks,
Dan