The cleaning cycle is not complete (Jura F9)

Do you mean the Jura Impressa C65? If you are prompted to clean the machine, first touch and hold the Maintenance button for ~2 seconds. You will be prompted to empty the tray. Empty both the drip tray and the grounds container. Replace these. Press Rinse and place a container under the spout. Touch the Maintenance button again. Wait while the water flows into the container. When the water stops flowing, the LCD screen will change from "Cleaning" to "Add tablet". Open the cover of the filler funnel for coffee grounds and place the Jura cleaning tablet in the filler funnel. Close the cover. Touch the Maintenance button again. Wait for the Cleaning cycle message to be replaced by the "Empty Tray" message. Empty the drip tray and coffee ground container again and replace them. The coffee maker will be ready to use when you see Espresso Heating. The procedure for descaling is in the manual.

The instructions are available on the product site, https://www.shopjura.com/impressa-c65.html , under the Manuals tab. The current link is https://us.jura.com/-/media/global/pdf/manuals-global/home/IMPRESSA-C60-C65/download_manual_jura_C60-C65_ul.pdf?la=en&hash=A918AF729D1132A17AF6A80C45F95D8CCC692ACE&em_force=true . The section on cleaning the super automatic coffee maker are in chapter 5, which starts on page 30. The section on Cleaning starts on page 37. The section on Descaling starts on page 39.

I hope this helps.

Cindy Wells

At the time of set up, Jura instructions ask activating the use of Filter cartridges. This eliminates reminders for descaling.
Solution:
Throw away the filter cartridges that are expensive, ineffective & block descaling reminders.
Descale the machine every three months using manual descaling method. See link for instructions. Services Unlimited Inc Parts Guru Since 1988

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edward_bbd2c7ff4ee1828a

Hi, I made a video how to fix your Jura step by step, good luck,,
http://fixandparts.wix.com/nicknicoloudis#!jura-coffee-machine/c15gy

Hi all, I have the exactly same problem on my Gaggenau CM470 however the drip tray is clean and the contacts in the back is also 100% clean.. I wonder if its possible to disable the sensor/switch on a CM470 ?

How are you doing the clean cycle ?
You should put a tablet in the coffee grounds front lid.
Push the clean button on the inside front panel.
The machine will ask you to open tap and empty tray along the way.
Make sure it does the full cycle.

machine is most likely clogged with old coffee grounds and needs a good cleaning cycle malf 8 is problem with the stoke of the piston can not make a complete cycle thur get your book out for machine and read list for cleaning machine follow remove power cord for a few mins. let machine cool down if hot from prior use then plug back in power up and do cleanning cycle with tablet follow book worst case would be oring seals on piston are no good or very dry making machine work to hard to move piston in this case service is needed good luck steve

Open the preground coffee lid, drop a cleaning tablet in it, let it do it's tablet cleaning cycle. After cycle empty water out of tray and clean.

Make sure your water tank to fill, when you start the clean process, and the tray is empty and wiped down. Then add a 500ml container under the spout rather than let the water go into the tray.
Also if you have not serviced the machine for about 5,000 cups this can occur.

Insert the tray-all of it except the grounds container.  The message disappears and you can wait until the machine continues it's cycle and then asks to empty the tray.  Empty the tray and place the grounds container back inside.  Whew, I've done this a few times over the years when I am rushing but it fixes it every time.