The color convergence seems to be on the fritz. all of the images on the screen have red blue and green shadows around them. I have tried the magic focus system, but it shuts down quickly and the number 5 pops up on the lower right portion of the screen. Is there a cheap fix?
How do i access the convergence on my big screen
The convergence ic's need to be replaced. There may also be several resistors in the same area that are burned and need to be replaced.
Your TV most likely has one or more possible problems.
Problem #1: Convergence Chip Failure ( common problem )
Here are some of the most common symptoms and example photos of a convergence problem
Here is a quick test....
Using your original remote go-to the tv settings then goto the convergence section.
Try to adjust the red and then the blue convergence.
You should be able to move them up, down, left, and right.
If you can't move them in all directions your convergence chips are bad and should be replacedhitachi television repair - 2c07611.png common problem.
Solution #1
You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.
Problem #2 CRT Fluid is Cloudy
Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.
TVhitachi television repair - 2c07611.pngter fluid change
Solution #2
What you will need to do is replace the coolant and clean the crt. You can get a repair kit from www.TvRepairKits.com that includes replacement coolant, photos. instructions, etc.
Red green & blue r off changed convergence chips & resistors that were burned out magic focus starts but stops on red at the 3rd line and than #5 comes up on the right bottom corner of the screen tried manually to focus but lines will not move why i need my tv back bad any suggestions thanks
I was watching tv last night and all of a sudden a red ray of light went across the screen.
Then the tv turned off and the power button started flickering red. does anyone have any suggestions ?
I have one of these sets and after replacing the convergence ic's you need to get into the factory menu's and this is done by taking the speaker cover off and then the center panel behind the speaker cover as you look in to the set at the convergence board you will see a little green button on the left corner of the convergence board towards the front of the set. There are specific procedures to set the convergence in the factory menu's but if you go slow and pay attention it can be done in a relativly short time.
Hitachi TV, screen Red need to fix 1
Hitachi TV, screen Red need to fix 1
×
I have this numbers and letter on the top of my hitachi tv C 2546TH 311 how do i remove it ?
I had the same problem. I could not afford a new TV.
I called Hitachi for a local Hitachi repair center.
They replaced the convergence modules and cleaned the picture tubes.
They soldered some other items.
They explained that the convergence modules are the common repair for these TVs.
This repair is not for the non-professional.
The costs $512 with tax and one hour. I live in the New York Area.
The cost may be different in other areas.
$500 repair vs $1500 new TV?
Now my TV is like new.
I hope this helps.
I have red and blue across the top of screen how do we fix it.
SOURCE: hitachi television repair
Good Day,
Sounds like the TV's convergence circuit has failed:
*Call an Authorized Service Center and them give you an estimate cost of the repair, or
*Repair it your self; get KIT 10 locally or B&D Enterprises
1-800-458-6053; www.bdent.com.
Good luck, big IRISH.
11,079 views
Usually answered in minutes!
Same issue but when using the magic focus it goes thru blue and green quickly and takes 20-30 seconds to get through the red. Magic focus does not fix. Alignment of colors in center appear closer to normal but red aligns higher toward bottom of screen and red aligns lower toward top of screen.
my colors are not in sync anymore and my magic focus doesn't work after a few seconds on magic focus 5 just apears on the bottom of the scream.
I have a Hitachi 61SWX10B, which was purchased in 2002, and my TV started having the color converse problem/3D type of issue a few days ago. I also stated having rpoblems with the sound where about a minute after I turn on this TV, either the sound disappear or it starts making some wiered noise.
i have blue convergence problems is it true that if i change the convergence correction circuit 6 channels and output muting circuit this will fix my problem there should be two of these ic's ? and what circuit board are they located on ?
hitachi 53 projection tv with major convergence problem. red image is approximately 2" to the right of other images. tried the magic button to no avail. Wonder what next step is if any.
hitachi model 51SWX20B purchased 3/6/03. Magic Focus gets 5 in lower left of screen. Tried manual focus, and green lines on left side of screen are wavy. Aligned red and blue, so picture is clear, but left side of screen is vertically wavy.
I'm having a similar problem. Mine is a green red ghosting. The red seems to be ghosting about 2 inches below the green across the top third of the screen. I opened up the TV and there is a distinct 1/4 grayish black line running just to the left of center on the red lens. Any relation to my problem? How can I fix this? Is it simply out of convergence? How could this just happen one day? Any help, suggestions or input is greatly appreciated.
I have ghosts when i first my tv on after 20 min i use majic focus and that clears the problem but if i turn the tv set off and back on the ghst are there
Yes, i too have the same problem. I cannot converge the 3 colors using the interface, so I wonder if it may be a problem with the lamps. The green seems to be the most off.
I have the same problem - blue is ghosting - majic focus runs for a minute, then goes blank and shows a number 5
Hitachi # 53FDX20B same problem. What is the
cost range for a technician to come to your home? Magic Focus results in same manner.
ghost and red color around images but if i let the set warm up for 20 min the magic focus will sometimes work to correct the problem
same problem except after magic focus 10 flashes mainly green ghost sometimes worse than others. tried cleaning, got better picture but still had ghost problem
Red ghosts suddenly appreared. Check out transreceive by connecting to other TV, no problem. Replaced S Video cable to TV. Tried Magic Focus but no fix
Having the same problem with the reds, blues, and greens. Sets about 5 years old. What to do???
Blue color seems to be out of adjustment. Cannot adjust with Majic Focus or manually with controls. What do I do.
hitachi tv has ghosts
all colors have a shadow and after the television is on awhile it will shut off.. Any suggestions on how to fix it
red shadow and tv shuts off occasionally
yea my screen blue lens is unlined looks as if it has ghosts
Was watching TV when it shut off. Power light blinked 5-10 times and turned back on. Now I have Blue shadows especially around the edges.
Our Hitachi also has the red blue and green lines toward the top left hand side of the screen as though the colors were not lined up properly anymore. We also tried the magic focus but it did not work at all.
I just have blue around the images. Although I have a 51 in.
color is fuzzy and the lines on the tv is wavey--how do i fix the convergence or where do i go to get instructions on doing this on a hitachi model 50ux22ba
I have a hitachi 53sdx89ba rear projection TV. I have convergence issues - primarily in red. After hours of on-line research, I have replaced both convergence IC's (110's upgraded to STK 394 160 E). I have carefully checked all resistors and replaced bad RK46 (1.5ohm, 1W). My operating manual and available service manuals (bought on-line) and instructions from TV Repair Kits.com do not seem to work for manual DCAM adjustment on this Hitachi TV. For example, if I press and hold Majic Focus I get two screens, first Center Mode then Static mode, but I can not move red cross or red line with any buttons on remote. These screens on not described in service manual, etc. I can not access the grid mode that is supposedly available. For example, the instructions from TV Repair Kits that begins:
Press Magic Focus to begin magic focus
3) Press magic focus again during the magic focus process to get the "stop" screen
4) While stop screen is up, press STATUS or INFO on the remote control (R/C) to bring you to DCAM mode and
the service grid
... do not give access to service grid.
I have read countless blogs and boards and I can not determine if the hardware fix is bad (I find this hard to believe as I carefully soldered the two IC's in and checked and rechecked all the IC board resistors) or if I have a Software/Menu access issue. I have seen one poster say a fuse on the convergence board could be out, but I can not find the fuse.
Any suggestions appreciated. I have about 30 hours into this repair and am too stubborn to give up now.
×