Onkyo Ht-r510 5.1 Channel 100 Watt Av Receiver Logo

Related Topics:

A
Anonymous Posted on Dec 17, 2013
Be the first to answer

I have an ONKYO AV RECEIVER HT-R510 when the set is cold it starts up and within 15 mins it cut off

Answer This Question

3 Related Answers

Anonymous

  • 5 Answers
  • Posted on Feb 13, 2010

SOURCE: My Onkyo HT-R510 will shut down after several

Might be over heating. Make sure you don't have anything sitting directly on top of it. I even put a little fan blowing outward at the back of my system to keep it cool.

Ad
Grubhead

Grubhead

  • 5755 Answers
  • Posted on Mar 21, 2010

SOURCE: Selecting phono preamp for Onkyo HT-R510

The magnetic cartridge preamp should work with the turntable, as presumably it will have a magnetic cartridge in it. The only reason that the amp states "magnetic" is that some very old turntables have ceramic cartridges which should not be connected to that terminal. Even if the turntable had a "ceramic" it could be replaced with a magnetic one!

patb9999

  • 3 Answers
  • Posted on Jun 24, 2010

SOURCE: Onkyo TX-DS777 does not retain settings after power loss

No internal battery, a large "SuperCap" on the main board acts as one. Look for C8007, 0.1 F, 5.5V.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

What's the error M1.04/19912A50?
The error code M1.04/19912A50 on your Onkyo AV receiver HT-R398 typically indicates a firmware or software-related issue. To resolve this problem and reset your receiver, you can follow these steps:
  1. Power Cycle the Receiver:
    • Turn off the receiver and unplug it from the power source.
    • Wait for about 10-15 minutes to ensure that all internal components have fully powered down.
    • Plug the receiver back in and turn it on.
  2. Factory Reset:
    • If the error persists after power cycling, you may need to perform a factory reset to restore the receiver to its default settings. Note that this will erase all your custom settings, so make sure to back up any important configurations if possible.
    • To perform a factory reset, refer to your receiver's user manual for specific instructions. Typically, this involves pressing and holding specific buttons on the front panel while powering on the receiver. The exact combination of buttons may vary by model.
  3. Firmware Update:
    • Ensure that your receiver's firmware is up to date. Visit the Onkyo website and check if there are any firmware updates available for your HT-R398 model. If updates are available, follow the provided instructions to update the firmware.
  4. Contact Customer Support:
    • If the issue persists after trying the above steps, it's a good idea to contact Onkyo customer support or visit their official support website. They may be able to provide specific guidance or solutions for the error code you're encountering.
Remember to consult your receiver's user manual for model-specific instructions, as the steps to reset or update firmware can vary between different Onkyo models. Additionally, be cautious when performing a factory reset, as it will erase all settings and return the receiver to its default state.
Read full answer
Oct 01, 2023 • Onkyo Audio Players & Recorders
0helpful
1answer

Want to control my HT-R510 with my TV remote. Need Onkyo code to control this HT-R510
You should indicate you remote.
In any case, if code is not in your remote you should follow indications for No code
If you don't have a manual, look for one using google,and terms manual, make and model of your remote
Read full answer
Aug 26, 2015 • Onkyo Audio Players & Recorders
0helpful
2answers

After turned on the power, the unit shuts down immidietly
There is a problem in either the power supply or amplifier output stages. The unit is programmed to shut down in such an event to protect other circuitry.

Using a schematic see if you can isolate the power going to the output stages. If unit stays on then the anomaly is in power amp stages. If it still shuts off problemo is in power supply - check diodes and capacitors.
Read full answer
Mar 12, 2015 • Onkyo Ht-r510 5.1 Channel 100 Watt Av...
0helpful
2answers

Where is the IR receiver on an Onkyo AV Receiver HT-R390 / HT-R290?
In back bottom right on the HT-R640
Read full answer
Jun 21, 2014 • Audio Players & Recorders
0helpful
1answer

Rca ouputs to onkyo HT-R510
http://www.manualslib.com/manual/302223/Onkyo-Ht-R510.html?page=10#manualhere is a link to the manual look under connections a/v
Read full answer
Apr 19, 2014 • RCA Audio Players & Recorders
0helpful
1answer

Intermittent speaker performance - receiver issue - not a speaker issue
Matt,

Have you checked/cleaned the leads on each speaker as one bad lead or speaker can pull/push extra power from/to other speakers causing shorts, this is likely not the case but could be the easy fix. Try cutting one speaker out at a time rotating which one is disconnected to see if this fixes the issue and possibly points out either a bad speaker or connection.
Read full answer
Dec 04, 2013 • RCA Onkyo Ht-r510 Receiver 6.1 Channel...
0helpful
1answer

Onkyo HT-R510
have you tried to reset it to factory defaults yet? If it has a vcr button on the front, then hold the vcr button and press power...it should say reset on the front. Might not help, but worth a try.
Read full answer
Dec 04, 2013 • Onkyo TX-SR601 Receiver
0helpful
1answer

Selecting phono preamp for Onkyo HT-R510
The magnetic cartridge preamp should work with the turntable, as presumably it will have a magnetic cartridge in it. The only reason that the amp states "magnetic" is that some very old turntables have ceramic cartridges which should not be connected to that terminal. Even if the turntable had a "ceramic" it could be replaced with a magnetic one!
Read full answer
Mar 21, 2010 • Onkyo HT510 Receiver
2helpful
1answer

Have ajustments all screwed up
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [ON/STANDBY] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
 Note that resetting the AV receiver will delete your
radio presets and custom settings.
Read full answer
Feb 10, 2010 • Onkyo HT-S9100THX 7.1 Channel Receiver and...
0helpful
1answer

My Onkyo HT-R510 will shut down after several
Might be over heating. Make sure you don't have anything sitting directly on top of it. I even put a little fan blowing outward at the back of my system to keep it cool.
Read full answer
Dec 04, 2009 • Onkyo TX-SR501 Receiver
Not finding what you are looking for?

View Most Popular

Ht-r510 5.1 Channel 100 Watt Av Receiver

  • Audio Players & Recorders

Related Question

What's the error M1.04/19912A50?

  • Onkyo Audio Players & Recorders

82 views

Ask a Question

Usually answered in minutes!

Popular Questions

Code for Verizon FIOS remote Control

Onkyo TX-SR605 Receiver

My Onkyo tx-sr606 7.1 receiver turns off by itself

Onkyo TX-SR606 Receiver

My Onkyo AV receiver keeps shutting off randomly

Onkyo Audio Players & Recorders

Code for Sony BDP-S300 Blu-ray player on Onkyo remote

Onkyo TX-SR605 Receiver

What is error code NG:LCRSLSRBLBR"

Onkyo TX-SR605 Receiver

Latest Celebrity Headphones Report
Latest Celebrity Headphones Report

View all Fixya Reports

Top Onkyo Audio Players & Recorders Experts

Grubhead
Grubhead

Level 3 Expert

5755 Answers

Grand Canyon Tech
Grand Canyon Tech

Level 3 Expert

3867 Answers

John
John

Level 2 Expert

510 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...