Bizhub 470 not switching on ?

if after this procedure code come back replace the fuser, attempt again machine my catch on fire that would ruin a perfectly good day

1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and
check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Turning the Power On or Off - Konica Minolta Online Manuals

manuals.konicaminolta.eu/bizhub-C554-C454-C364.../id10-0061.html

bizhub C554 C454 C364 C284 C224 ... The Main Power Switch of the machine and thePower key on the Control Panel. No. Name, Description. 1. Main Power Switch. Press this switch when turning on or off the main power of this machine or ...

[PDF]C7000/C7000P/C6000/C70hc/ C6000L

myworks.sindoh.com/upload2/.../d37800822888835787371.pdf

KONICA MINOLTA Confidential. 2. C-2721, Intermediate .... v) Execute Printercontroller calibration for every output profile. (Standard ..... Start CWS5 and login to a Fiery controller. ii) Click [Calibrate] ...... If FD skew doesn't remain,. FD skew ......*A1DURX01: For bizhub PRESS C7000/C6000 and bizhub PRO C6501. 2.

replace the fuser unit.

If the code comes back do not reset, you are messing with the Fuser the Hot part. Continuing to reset without a technician looking at and or replacing it, the fuser can catch on fire and that would ruin a perfectly good day.


Then reset.

use this procedure:

1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after
and check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after
and check if the machine starts correctly.


IF THIS CODE COMES BACK GET A TECH YOU HAVE A PROBLEM WITH FUSER WHICH CAN CATCH ON FIRE RUINING A PERFECTLY GOOD DAY.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

do below once if the code comes back replace the fuser continue reset cause fire ruining a perfectly good day


1. Turn ON the main power switch (SW1).
2. With the Utility/Counter key pressed, turn ON the power switch (SW2).
3. Press [Trouble reset] to release a trouble with [OK] displayed.
4. Turn OFF and ON the power switch (SW2).

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Press the Trouble reset switch on the tech.rep.setting switches board to reset a malfunctions,or open and close the front door and turn OFF the copier wait 1 minute and turn ON.

if the code does come back DO NOT RESET the machine again! It is indicating a problem the code you are resetting is the fuser and it can catch on fire! That will ruin a perfectly good day!!!
ENSURE YOU WAIT 10 SECONDS

1.Turn OFF the main power switch. (Located inside machine) Leave control power switch in the on position.)
2.Turn main power switch ON while pressing the Utility/Counter key.
3.Touch [Trouble Reset].
4.Check to make sure that [OK] is displayed and the it has been reset.
5.After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

There is no c3451 code in the bizhub 350 service manual.

C2451: New Transfer Cleaner Unit resetting failure

1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the Main Power Switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Your not giving enough information. But i would make sure that the interface cable between the optics and the print engine are intact. Its the fat cable with the high density pins on the right side of the machine near the back. (external) Make sure this is reseated, otherwise you will be tearing into control boards.