When trying to manually stop recording , the STOP button won;t stop the recording.

The Wurlitzer 2900 is a jukebox that plays 45 RPM records. To stop it from playing the same record over and over, you can try the following steps:

1. Locate the jukebox's control panel: The control panel should have buttons that allow you to select and play records, as well as buttons to control the volume and lighting.
2. Press the stop button: The stop button will usually be labeled "Stop" or have a red triangle symbol. Pressing this button should stop the jukebox from playing the current record and return it to the selection mode.
3. Change the record: Use the jukebox's control panel to select a different record to play.
4. Adjust the play mode: The Wurlitzer 2900 may have a setting that determines how many times it will play a record before moving on to the next selection. You can check the jukebox's manual or settings menu to see if this is the case, and adjust it if necessary.

If these steps do not work, there may be a mechanical issue with the jukebox. In this case, it is recommended that you seek the assistance of a professional technician to diagnose and repair the problem.

Have you tried reading your owner's manual ... or tried calling Olympus Customer Service?

I would suggest to read on the owners manual first before operating your machine.and you can avail of the warranty if you found problem n your playaer...

Hi , disconnet the vcr wait few minutes and replug it
vcr suppose to be reset /if not lok for a small door
you should found a boutton whit inscription said timer press it and set it up to 0000 clock timer then its should be ok./or you can let it go and he will stop is sequence by it self.
good luck

Have had the same issue with a single handset. Finally located our manual:
1. Press and hold MEMO (FAST FORWARD) button until you hear a beep.
2. Record your memo, speaking from approx 15cm away.
3. As soon as you have finished speaking, press ON-OFF/STOP button to stop recording.
Hope this helps :)

Your Digital Voice Recorder has no on/off button or switch.
Just make sure you press the Stop button after you finished using it, to stop any activity.

You can download brochures/manuals for your
DS-330 Digital Voice Recorder from here: http://www.olympusamerica.com/CPG_SECTION/cpg_archived_product_details.asp?id=859&fl=8

First off I assume you have the manual for you're 5700. if not a PDF copy is here
http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000027911.pdf

Assuming you have a standalone tape deck that has phono inputs and outputs connection and recording recording should be easily achieved.
Forget the coaxial unless of course your tape deck has digital outputs.
Assuming it hasn't just connect the two output sockets from the tape dec which may be labelled REC out left and REC out right to the Line in (L) and Line (R) of the CD recorder.
The physical setup is now complete.
The increment level they refer to in the manual offers you a choice of 3 final decibel output levels in other words how loud it will be when it is finally recorded onto the disc.

the last paragraph on page 16 is relevant to the setup described above.

Page 15 of your manual is all you need to achieve tape transfer to CD.
follow the steps below and choose ANALOG the source to be played is your tape deck so once the process has begun press the play button on your tape deck and you should get a decent recording. Leave everything else at their default settings until you get a better understanding of how to tweak your recordings.
Personally I transfer audio tapes directly to my PC and Audio edit them until they are perfect but I've been doing this for years.

Good luck


here's a snippet

To record from an external source:
1. Turn power ON.
2. Place a recordable audio disc (CD-R or CD-RW) label side up
in TRAY II.
3. Close TRAY II. (When a blank disc is placed in TRAY II, the display
will show BLANK.)
4. Press INPUT until the source you want to record is selected.
DIGITAL OPTICAL:
record a source connected to the DIGITAL IN (OPTICAL) terminal.
DIGITAL COAXIAL:
record a source connected to the DIGITAL IN (COAXIAL) terminal.
ANALOG:
record a source connected to the analog LINE IN jacks.
5. Select the desired mode of track division (track number
assignment) by pressing the MANUAL/AUTO button (see the
ADVANCED RECORDING section for more information).
6. Press the RECORD button.
The unit enters record pause mode.
The PAUSE [ ] icon and REC blink on the display.
7. Press the PLAY (ENTER) [ ] button of TRAY II to start recording.
8. Play the source to be recorded.
• During digital recording, if the input signal stops for 5 seconds,
recording will stop.
• During analog recording, if the input signal stops for 20 seconds,
recording will stop.
• If the unit detects copy-prohibit signals during recording,
CAN’T COPY appears on the display and recording is stopped.
To stop recording: Press the STOP [] button
To temporarily pause recording: Press the PAUSE [ ] button.
Remember that every time recording is paused or stopped,
a new track number will be assigned.

How to Record:
1. Make sure HOLD switch (on side of unit with pocket clip) is set to off position (slide to right is off - to left would be hold)
2. For best results set unit with mic(rophone) which is on top of unit toward sound source and press REC/STOP button (Top button on front of unit just below LCD display). Recording will begin and will be indicated on LCD display.
> Red Record LED will be on and the message number, recording time will be displayed on the LCD.
3. To stop recording, press REC/STOP button one time.
* If no other buttons are pressed within 1 minute at stop position, it will power off automatically.
4. Pause during recording by simply pressing MODE/PAUSE button- press button again to resume.

There is a Voice Operated System (VOS) Recording button on left side also. You can record with voice activation to conserve recording space but I have found that you lose a portion of the recorded sound as it activates and if there is no sound for a very few minutes the unit powers off and you will get nothing further recorded. I recomend just keeping VOS in off position.

5. To erase a recording: Select the message number you want to erase and while it is stopped (the message number will appear in LCD with the length of recording showing also)
Press and hold the ERASE button until the LCD begins blinking "ERASE" then, while it's blinking simply press the erase button again and the recording will be erased.

6. To play back a recorded message find your message by "toggling" the switch on the right side of the unit that says INDEX. That switch is the fast forward/reverse play etc. To Play simply push the switch in. This button/switch takes a little practice to use but the Play portion is straight forward. Use the front buttons to pause and stop during playback.

Hope this helps.

can't record on the my Olympus VN-1000
+ I press rec button and it just shows rec in display (no recording time is shown ONLY rec)
+ there is no play back  or stop function

+ i can only stop  rec by removing batteries (stop or play will stop rec only ONCE - but there is no  useful function - such as play or stop or rec.)
+ I tried all trouble shooting tips in manual  with no effect 
+  i cleaned the spring contacts inside battery compartment that interface with the  batteries
+ it was barely used - and has not been used for a 1 year ( no batteries were inside it )     it was inside a drawer
THANK YOU 

If you press the play button while in FM mode it will start to record then press stop to stop.